[CPUFREQ] Move x86 drivers to drivers/cpufreq/

Signed-off-by: Dave Jones <davej@redhat.com>

arch/x86/Kconfig

@@ -1848,7 +1848,7 @@ config APM_ALLOW_INTS
 
 endif # APM
 
-source "arch/x86/kernel/cpu/cpufreq/Kconfig"
+source "drivers/cpufreq/Kconfig"
 
 source "drivers/cpuidle/Kconfig"
 

arch/x86/kernel/cpu/Makefile

@@ -30,7 +30,6 @@ obj-$(CONFIG_PERF_EVENTS)		+= perf_event.o
 
 obj-$(CONFIG_X86_MCE)			+= mcheck/
 obj-$(CONFIG_MTRR)			+= mtrr/
-obj-$(CONFIG_CPU_FREQ)			+= cpufreq/
 
 obj-$(CONFIG_X86_LOCAL_APIC)		+= perfctr-watchdog.o
 

arch/x86/kernel/cpu/cpufreq/Makefile

@@ -1,21 +0,0 @@
-# Link order matters. K8 is preferred to ACPI because of firmware bugs in early
-# K8 systems. ACPI is preferred to all other hardware-specific drivers.
-# speedstep-* is preferred over p4-clockmod.
-
-obj-$(CONFIG_X86_POWERNOW_K8)		+= powernow-k8.o mperf.o
-obj-$(CONFIG_X86_ACPI_CPUFREQ)		+= acpi-cpufreq.o mperf.o
-obj-$(CONFIG_X86_PCC_CPUFREQ)		+= pcc-cpufreq.o
-obj-$(CONFIG_X86_POWERNOW_K6)		+= powernow-k6.o
-obj-$(CONFIG_X86_POWERNOW_K7)		+= powernow-k7.o
-obj-$(CONFIG_X86_LONGHAUL)		+= longhaul.o
-obj-$(CONFIG_X86_E_POWERSAVER)		+= e_powersaver.o
-obj-$(CONFIG_ELAN_CPUFREQ)		+= elanfreq.o
-obj-$(CONFIG_SC520_CPUFREQ)		+= sc520_freq.o
-obj-$(CONFIG_X86_LONGRUN)		+= longrun.o  
-obj-$(CONFIG_X86_GX_SUSPMOD)		+= gx-suspmod.o
-obj-$(CONFIG_X86_SPEEDSTEP_ICH)		+= speedstep-ich.o
-obj-$(CONFIG_X86_SPEEDSTEP_LIB)		+= speedstep-lib.o
-obj-$(CONFIG_X86_SPEEDSTEP_SMI)		+= speedstep-smi.o
-obj-$(CONFIG_X86_SPEEDSTEP_CENTRINO)	+= speedstep-centrino.o
-obj-$(CONFIG_X86_P4_CLOCKMOD)		+= p4-clockmod.o
-obj-$(CONFIG_X86_CPUFREQ_NFORCE2)	+= cpufreq-nforce2.o

drivers/cpufreq/Kconfig

@@ -1,3 +1,5 @@
+menu "CPU Frequency scaling"
+
 config CPU_FREQ
 	bool "CPU Frequency scaling"
 	help
@@ -177,4 +179,10 @@ config CPU_FREQ_GOV_CONSERVATIVE
 
 	  If in doubt, say N.
 
-endif	# CPU_FREQ
+menu "x86 CPU frequency scaling drivers"
+depends on X86
+source "drivers/cpufreq/Kconfig.x86"
+endmenu
+
+endif
+endmenu

drivers/cpufreq/Kconfig.x86

@@ -1,15 +1,7 @@
 #
-# CPU Frequency scaling
+# x86 CPU Frequency scaling drivers
 #
 
-menu "CPU Frequency scaling"
-
-source "drivers/cpufreq/Kconfig"
-
-if CPU_FREQ
-
-comment "CPUFreq processor drivers"
-
 config X86_PCC_CPUFREQ
 	tristate "Processor Clocking Control interface driver"
 	depends on ACPI && ACPI_PROCESSOR
@@ -261,6 +253,3 @@ config X86_SPEEDSTEP_RELAXED_CAP_CHECK
 	  option lets the probing code bypass some of those checks if the
 	  parameter "relaxed_check=1" is passed to the module.
 
-endif	# CPU_FREQ
-
-endmenu

drivers/cpufreq/Makefile

@@ -13,3 +13,29 @@ obj-$(CONFIG_CPU_FREQ_GOV_CONSERVATIVE)	+= cpufreq_conservative.o
 # CPUfreq cross-arch helpers
 obj-$(CONFIG_CPU_FREQ_TABLE)		+= freq_table.o
 
+##################################################################################d
+# x86 drivers.
+# Link order matters. K8 is preferred to ACPI because of firmware bugs in early
+# K8 systems. ACPI is preferred to all other hardware-specific drivers.
+# speedstep-* is preferred over p4-clockmod.
+
+obj-$(CONFIG_X86_POWERNOW_K8)		+= powernow-k8.o mperf.o
+obj-$(CONFIG_X86_ACPI_CPUFREQ)		+= acpi-cpufreq.o mperf.o
+obj-$(CONFIG_X86_PCC_CPUFREQ)		+= pcc-cpufreq.o
+obj-$(CONFIG_X86_POWERNOW_K6)		+= powernow-k6.o
+obj-$(CONFIG_X86_POWERNOW_K7)		+= powernow-k7.o
+obj-$(CONFIG_X86_LONGHAUL)		+= longhaul.o
+obj-$(CONFIG_X86_E_POWERSAVER)		+= e_powersaver.o
+obj-$(CONFIG_ELAN_CPUFREQ)		+= elanfreq.o
+obj-$(CONFIG_SC520_CPUFREQ)		+= sc520_freq.o
+obj-$(CONFIG_X86_LONGRUN)		+= longrun.o
+obj-$(CONFIG_X86_GX_SUSPMOD)		+= gx-suspmod.o
+obj-$(CONFIG_X86_SPEEDSTEP_ICH)		+= speedstep-ich.o
+obj-$(CONFIG_X86_SPEEDSTEP_LIB)		+= speedstep-lib.o
+obj-$(CONFIG_X86_SPEEDSTEP_SMI)		+= speedstep-smi.o
+obj-$(CONFIG_X86_SPEEDSTEP_CENTRINO)	+= speedstep-centrino.o
+obj-$(CONFIG_X86_P4_CLOCKMOD)		+= p4-clockmod.o
+obj-$(CONFIG_X86_CPUFREQ_NFORCE2)	+= cpufreq-nforce2.o
+
+##################################################################################d
+