Kavya Nunna
49aacfeee4
Disable pmk8350 vadc node for litomagnus and orchid as the channels are not used. Change-Id: Idc6827bfa371073d77057cc501eeeaa5fb08364e
147 lines
2.6 KiB
Devicetree
147 lines
2.6 KiB
Devicetree
#include "lito-mtp.dtsi"
|
|
#include <dt-bindings/iio/qcom,spmi-vadc.h>
|
|
|
|
&soc {
|
|
|
|
};
|
|
|
|
&usb_qmp_dp_phy {
|
|
/delete-property/vdd-supply;
|
|
vdd-supply = <&L11A>;
|
|
};
|
|
|
|
&sde_dp {
|
|
vdda-0p9-supply = <&L11A>;
|
|
};
|
|
|
|
&sde_dsi {
|
|
qcom,dsi-default-panel = <&dsi_sw43404_amoled_fhd_plus_cmd>;
|
|
};
|
|
|
|
&sde_dsi1 {
|
|
status = "disabled";
|
|
};
|
|
|
|
&mdss_mdp {
|
|
connectors = <&sde_wb &sde_dsi &sde_dp &sde_rscc>;
|
|
};
|
|
|
|
&swr0 {
|
|
wsa883x_0221: wsa883x@02170221 {
|
|
compatible = "qcom,wsa883x";
|
|
reg = <0x02 0x02170221>;
|
|
qcom,spkr-sd-n-node = <&wsa_spkr_en1>;
|
|
qcom,bolero-handle = <&bolero>;
|
|
cdc-vdd-1p8-supply = <&S4A>;
|
|
|
|
qcom,cdc-vdd-1p8-voltage = <1800000 1800000>;
|
|
qcom,cdc-vdd-1p8-current = <20000>;
|
|
qcom,cdc-vdd-1p8-lpm-supported = <1>;
|
|
qcom,cdc-static-supplies = "cdc-vdd-1p8";
|
|
};
|
|
|
|
wsa883x_0222: wsa883x@02170222 {
|
|
compatible = "qcom,wsa883x";
|
|
reg = <0x02 0x02170222>;
|
|
qcom,spkr-sd-n-node = <&wsa_spkr_en2>;
|
|
qcom,bolero-handle = <&bolero>;
|
|
|
|
cdc-vdd-1p8-supply = <&S4A>;
|
|
qcom,cdc-vdd-1p8-voltage = <1800000 1800000>;
|
|
qcom,cdc-vdd-1p8-current = <20000>;
|
|
qcom,cdc-vdd-1p8-lpm-supported = <1>;
|
|
qcom,cdc-static-supplies = "cdc-vdd-1p8";
|
|
};
|
|
};
|
|
|
|
&wsa881x_0211 {
|
|
status = "disabled";
|
|
};
|
|
|
|
&wsa881x_0212 {
|
|
status = "disabled";
|
|
};
|
|
|
|
&wsa881x_0213 {
|
|
status = "disabled";
|
|
};
|
|
|
|
&wsa881x_0214 {
|
|
status = "disabled";
|
|
};
|
|
|
|
&lito_snd {
|
|
qcom,model = "lito-orchidmtp-snd-card";
|
|
qcom,wsa-max-devs = <2>;
|
|
qcom,wsa-devs = <&wsa883x_0221>, <&wsa883x_0222>;
|
|
qcom,wsa-aux-dev-prefix = "SpkrLeft", "SpkrRight";
|
|
};
|
|
|
|
|
|
&pm8150_rtc {
|
|
status = "disabled";
|
|
};
|
|
|
|
&pmk8350_adc_tm {
|
|
status = "disabled";
|
|
};
|
|
|
|
&pmk8350_vadc {
|
|
status = "disabled";
|
|
};
|
|
|
|
&pm7250b_qg {
|
|
qcom,use-cp-iin-sns;
|
|
};
|
|
|
|
&pm7250b_vadc {
|
|
smb1390_therm@e {
|
|
qcom,scale-fn-type = <ADC_SCALE_HW_CALIB_PM5_SMB1398_TEMP>;
|
|
};
|
|
};
|
|
|
|
&pm7250b_gpios {
|
|
smb_stat {
|
|
smb_stat_default: smb_stat_default {
|
|
pins = "gpio6";
|
|
function = "normal";
|
|
input-enable;
|
|
bias-pull-up;
|
|
qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
|
|
power-source = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&qupv3_se9_i2c {
|
|
qcom,clk-freq-out = <100000>;
|
|
status = "ok"
|
|
#include "smb1398.dtsi"
|
|
};
|
|
|
|
&smb1396 {
|
|
interrupts = <0x2 0xc5 0x0 IRQ_TYPE_LEVEL_LOW>;
|
|
interrupt-parent = <&spmi_bus>;
|
|
interrupt-names = "smb1396";
|
|
pinctrl-names = "default";
|
|
qcom,enable-toggle-stat;
|
|
pinctrl-0 = <&smb_stat_default>;
|
|
status = "ok"
|
|
};
|
|
|
|
&smb1396_div2_cp_master {
|
|
io-channels = <&pm7250b_vadc ADC_AMUX_THM2>;
|
|
qcom,parallel-input-mode = <1>; /* USBIN */
|
|
qcom,parallel-output-mode = <2>; /* VBAT */
|
|
qcom,min-ilim-ua = <1000000>;
|
|
status = "ok"
|
|
};
|
|
|
|
&smb1396_slave {
|
|
status = "ok"
|
|
};
|
|
|
|
&smb1396_div2_cp_slave {
|
|
status = "ok"
|
|
};
|