duff/android_kernel_motorola_sm6225
1
0 Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
Files
add9799fc66fa2fb2e1d3a23cde6a5a548f1ba79
android_kernel_motorola_sm6225/qcom/bengal-caprip-common-overlay.dtsi
T
tnchangj 91fe1157e5 dts:Caprip: Update the tune parameter 
- QC case 04971188
    - The problem is that the voltage of USB eye diagram is a little high.
    - The voltage range of the eye diagram is should in +-0.4V

Change-Id: I35429eda2e27d0735e6f1f1c2d7a9b5d45278843
Reviewed-on: https://gerrit.mot.com/1836837
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Ying Shen <shenying@motorola.com>
Reviewed-by: Xiangpo Zhao <zhaoxp3@motorola.com>
Submit-Approved: Jira Key
2023-05-31 17:01:03 -03:00

497 lines
11 KiB
Devicetree
Raw Blame History

/* Copyright (c) 2019, The Linux Foundation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 and
* only version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include "bengal-moto-common-overlay.dtsi"
#include "bengal-capri-pinctrl-overlay.dtsi"
#include "bengal-capri-display.dtsi"
#include "bengal-audio-overlay.dtsi"
#include "bengal-capri-awinic-audio-overlay.dtsi"
#include "bengal-caprip-touchscreen-overlay.dtsi"
#include "camera/bengal-camera-sensor-mot-caprip-overlay.dtsi"
#include "bengal-capri-fps.dtsi"
#include "bengal-capri-moto-thermal.dtsi"
&firmware {
android {
vbmeta {
compatible = "android,vbmeta";
parts = "vbmeta,boot,system,vendor,dtbo";
};
};
};
&qupv3_se4_2uart {
status = "ok"
};
&pm6125_gpios {
key_vol_up {
key_vol_up_default: key_vol_up_default {
pins = "gpio5";
function = "normal";
input-enable;
bias-pull-up;
power-source = <0>;
};
};
};
&tlmm{
capsense_sar_gpio_pins: capsense_sar_gpio_pins {
mux {
pins = "gpio36";
function = "gpio";
};
config {
pins = "gpio36";
drive-strength = <2>;
bias-pull-up;
input-enable;
};
};
};
&tlmm {
tlmm_gpio_key {
gpio_key_active: gpio_key_active {
mux {
pins = "gpio33";
function = "gpio";
};
config {
pins = "gpio33";
drive-strength = <2>;
bias-pull-up;
};
};
};
sar_int_default: sar_int_default {
mux {
pins = "gpio36";
function = "gpio";
};
config {
pins = "gpio36";
num-grp-pins = <1>;
drive-strength = <2>;
bias-pull-up;
};
};
sar_int_sleep: sar_int_sleep {
mux {
pins = "gpio36";
function = "gpio";
};
config {
pins = "gpio36";
num-grp-pins = <1>;
drive-strength = <2>;
bias-pull-up;
};
};
};
&soc {
gpio_keys {
compatible = "gpio-keys";
label = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&key_vol_up_default &gpio_key_active>;
vol_up {
label = "volume_up";
gpios = <&pm6125_gpios 5 GPIO_ACTIVE_LOW>;
linux,input-type = <1>;
linux,code = <KEY_VOLUMEUP>;
linux,can-disable;
debounce-interval = <15>;
gpio-key,wakeup;
};
assist_key{
label = "assist_key";
gpios = <&tlmm 33 0x1>;
linux,input-type = <1>;
linux,code = <KEY_SEARCH>;
debounce-interval = <15>;
linux,can-disable;
gpio-key,wakeup;
};
};
};
&sdhc_1 {
vdd-supply = <&L24A>;
qcom,vdd-voltage-level = <2960000 2960000>;
qcom,vdd-current-level = <0 570000>;
vdd-io-supply = <&L11A>;
qcom,vdd-io-always-on;
qcom,vdd-io-lpm-sup;
qcom,vdd-io-voltage-level = <1800000 1800000>;
qcom,vdd-io-current-level = <0 325000>;
pinctrl-names = "active", "sleep";
pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on
&sdc1_rclk_on>;
pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off
&sdc1_rclk_off>;
status = "ok"
};
&sdhc_2 {
vdd-supply = <&L22A>;
qcom,vdd-voltage-level = <2960000 2960000>;
qcom,vdd-current-level = <0 800000>;
vdd-io-supply = <&L5A>;
qcom,vdd-io-voltage-level = <1800000 2960000>;
qcom,vdd-io-current-level = <0 22000>;
vdd-io-bias-supply = <&L7A>;
qcom,vdd-io-bias-voltage-level = <1256000 1256000>;
qcom,vdd-io-bias-current-level = <0 6000>;
pinctrl-names = "active", "sleep";
pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
cd-gpios = <&tlmm 88 GPIO_ACTIVE_HIGH>;
status = "ok"
};
&ufsphy_mem {
compatible = "qcom,ufs-phy-qmp-v3-660";
vdda-phy-supply = <&L4A>; /* 0.9v */
vdda-pll-supply = <&L12A>; /* 1.8v */
vdda-phy-max-microamp = <51400>;
vdda-pll-max-microamp = <14200>;
status = "ok"
};
&ufshc_mem {
vdd-hba-supply = <&gcc_ufs_phy_gdsc>;
vdd-hba-fixed-regulator;
vcc-supply = <&L24A>;
vcc-voltage-level = <2950000 2960000>;
vccq2-supply = <&L11A>;
vcc-max-microamp = <600000>;
vccq2-max-microamp = <600000>;
qcom,vddp-ref-clk-supply = <&L18A>;
qcom,vddp-ref-clk-max-microamp = <100>;
qcom,vddp-ref-clk-min-uV = <1232000>;
qcom,vddp-ref-clk-max-uV = <1232000>;
status = "ok"
};
&sde_dsi {
qcom,dsi-default-panel = <&dsi_djn_nt36525c_652_video>;
};
&soc {
qcom,tz_gpio {
compatible = "qcom,tz_gpio";
tlmm-tz = <14>,
<15>,
<16>,
<17>;
};
};
&L21A {
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <3600000>;
qcom,init-voltage = <2800000>;
};
&qupv3_se0_i2c {
status = "ok"
sar_abov: abov_sar@20 {
status = "ok"
compatible = "abov,abov_sar_mmi_overlay";
reg = <0x20>;
cap_vdd-supply = <&L21A>;
interrupt-parent = <&tlmm>;
interrupts = <36 0x2>;
gpios = <&tlmm 36 0x2>;
pinctrl-names = "default";
pinctrl-0 = <&capsense_sar_gpio_pins>;
reg_array_len = <0x03>;
reg_array_val = <0x07 0x00 0x08 0x1B 0xFB 0x01>;
cap,use_channel_ch1 = <0x00>;
cap,use_channel_ch0 = <0x01>;
ch0_name = "capsense_top";
ch1_name = "capsense_bottom";
label = "AbovCapSense";
cap,channel_number = <0x02>;
cap,fw_mode_ret = <0x3A>;
};
sx933x@28 { /* SAR sensor */
compatible = "Semtech,sx933x";
reg = <0x28>;
pinctrl-names = "default","sleep";
pinctrl-0 = <&sar_int_default>;
pinctrl-1 = <&sar_int_sleep>;
Semtech,power-supply-type = <1>;
cap_vdd-supply = <&L21A>;
interrupt-parent = <&tlmm>;
interrupts = <36 0x02>;
interrupt-names = "sx933x_irq";
Semtech,nirq-gpio= <&tlmm 36 0x02>;
Semtech,button-flag = <0x03>;
Semtech,headset-reg-num = <4>;
Semtech,headset-reg = <
0x8074 0x08203515
0x802c 0x20000A9D
0x803c 0x20000A9D
0x801c 0x20000014>;
Semtech,reg-num = <85>;
Semtech,reg-init =<
0x8020 0x001F0000
0x4004 0x74
0x4008 0x00
0x4054 0x400
0x42C0 0x8000000
0x42C4 0x3F
0x800C 0x00
0x8010 0x00
0x8014 0x00
0x8018 0x00
0x801C 0x32
0x8024 0x10000A7E
0x8028 0x3DFF82D8
0x802C 0x20000A5E
0x8030 0x3FF78267
0x8034 0x20000A66
0x8038 0x3FBF82D5
0x803C 0x10000A76
0x8040 0x3FFE825F
0x8044 0x10000A76
0x8048 0x2FFF8268
0x804C 0x300004D4
0x8050 0x00
0x8054 0x303302
0x8058 0x2060000C
0x805C 0x24E67000
0x8060 0x00
0x8064 0x560000
0x8068 0x00
0x806C 0x1E001E00
0x8070 0x00
0x8074 0x305E02
0x8078 0x20600018
0x807C 0x46D47000
0x8080 0x00
0x8084 0x930000
0x8088 0x00
0x808C 0x1E001E
0x8090 0x20000
0x8094 0x102D00
0x8098 0x20600018
0x809C 0x2AD67000
0x80A0 0x00
0x80A4 0x00
0x80A8 0x00
0x80AC 0x00
0x80B0 0x00
0x80B4 0x50FF00
0x80B8 0x20600018
0x80BC 0x2AD67000
0x80C0 0x00
0x80C4 0x00
0x80C8 0x00
0x80CC 0x00
0x80D0 0x00
0x80D4 0x50FF00
0x80D8 0x20600018
0x80DC 0x2AD67000
0x80E0 0x00
0x80E4 0x00
0x80E8 0x00
0x80EC 0x00
0x80F0 0x00
0x80F4 0x100000
0x80F8 0x20600C00
0x80FC 0x00
0x8100 0x00
0x8104 0x00
0x8108 0x00
0x810C 0x00
0x8110 0x00
0x8124 0x4000004
0x8128 0x4000003
0x812C 0x00
0x8130 0x00
0x8134 0x00
0x8138 0x00
0x813C 0x00
0x8140 0x00
0x8144 0x00
0x8148 0x00
0x814C 0x00
0x81A4 0x1D00008
0x8020 0x001F001F
0x4280 0x000F
>;
Semtech,ref-phases-a = <3>;
Semtech,ref-phases-b = <4>;
status = "ok"
};
};
&qupv3_se1_i2c {
status = "ok"
#address-cells = <1>;
#size-cells = <0>;
nq@28 {
compatible = "qcom,nq-nci";
reg = <0x28>;
qcom,nq-irq = <&tlmm 70 0x00>;
qcom,nq-ven = <&tlmm 2 0x00>;
qcom,nq-firm = <&tlmm 31 0x00>;
qcom,nq-clkreq = <&tlmm 86 0x00>;
interrupt-parent = <&tlmm>;
interrupts = <70 0>;
interrupt-names = "nfc_irq";
pinctrl-names = "nfc_active", "nfc_suspend";
pinctrl-0 = <&nfc_int_active &nfc_enable_active
&nfc_clk_req_active>;
pinctrl-1 = <&nfc_int_suspend &nfc_enable_suspend
&nfc_clk_req_suspend>;
};
};
&soc{
mtp_batterydata: qcom,battery-data {
qcom,batt-id-range-pct = <15>;
df-serialnum = "SB18C85291";
#include "qg-batterydata-jk50-atl-4850mah.dtsi"
#include "qg-batterydata-jk50-scud-4850mah.dtsi"
#include "qg-batterydata-jk50-atl-flex-4850mah.dtsi"
#include "qg-batterydata-jk50-atl-unicoba-4850mah.dtsi"
#include "qg-batterydata-jk50-swd-4850mah.dtsi"
#include "qg-batterydata-jk50-atl-india-4850mah.dtsi"
};
};
&pmi632_vib {
qcom,vib-ldo-volt-uv = <3000000>;
qcom,vib-dis-short-long;
qcom,vib-dis-short-long-val = <80>;
qcom,vib-ldo-volt-uv-long = <2500000>;
};
&pmi632_qg {
qcom,qg-iterm-ma = <350>;
qcom,vbatt-cutoff-mv = <3200>;
qcom,vbatt-empty-mv = <3000>;
qcom,vbatt-low-mv = <3300>;
qcom,vbatt-low-cold-mv = <3500>;
qcom,battery-data = <&mtp_batterydata>;
qcom,rbat-conn-mohm = <10>;
qcom,cl-feedback-on;
qcom,cl-min-start-soc = <0>;
qcom,cl-max-start-soc = <5>;
qcom,cl-min-temp = <150>;
qcom,cl-max-temp = <450>;
qcom,cl-max-increment = <5>;
qcom,cl-max-decrement = <10>;
qcom,cl-min-limit = <200>;
qcom,cl-max-limit = <30>;
qcom,s3-entry-ibat-ua = <15000>;
qcom,s3-exit-ibat-ua = <35000>;
qcom,vbatt-empty-cold-mv = <3000>;
qcom,ignore-shutdown-soc-secs = <1800>;
qcom.hold-soc-while-full;
qcom,linearize-soc;
};
&pmi632_charger {
qcom,iterm-ma = <100>;
qcom,fcc-max-ua = <3000000>;
qcom,fv-max-uv = <4400000>;
qcom,usb-icl-ua = <3000000>;
qcom,thermal-mitigation = <3000>,
<2600>,
<2300>,
<1800>,
<1500>,
<1000>,
<600>,
<400>;
qcom,battery-data = <&mtp_batterydata>;
qcom,mmi-temp-zones = <0 4200 1000 0>,
<10 4200 1000 1000>,
<15 0 1000 1000>,
<45 0 3000 3000>,
<60 4200 2500 0>;
qcom,enable-charging-limit;
qcom,upper-limit-capacity = <65>;
qcom,lower-limit-capacity = <60>;
qcom,otg-cl-ua = <1000000>;
qcom,dc-unsupported;
qcom,wireless-unsupported;
qcom,usbeb-unsupported;
qcom,disable-suspend-on-collapse;
dpdm-supply = <&qusb_phy0>;
qcom,auto-recharge-soc = <99>;
mmi,ext-ovp-greater-12v;
};
&pmi632_rgb {
red {
label = "charging";
};
};
&spmi_bus {
qcom,pm6125@0 {
qpnp-power-on-mmi@800 {
compatible = "qcom,qpnp-power-on-mmi";
interrupts = <0x0 0x8 0x3 IRQ_TYPE_EDGE_BOTH>;
interrupt-names = "kpdpwr-bark";
};
};
};
&qusb_phy0 {
qcom,qusb-phy-init-seq = <0xf8 0x80
0x63 0x84
0x81 0x88
0xc0 0x8c
0x30 0x08
0x79 0x0c
0x21 0x10
0x14 0x9c
0x80 0x04
0x9f 0x1c
0x00 0x18>;
qcom,tune2-efuse-correction = <(-3)>;
};
Reference in new issue View Git Blame Copy Permalink