Shilpa Suresh
bcb1a8d659
Add the Scaling function type for the battery thermistor for the QM215 hardware. Change-Id: If468feab45af1603f730d0b01ebc26945c9d20d0
251 lines
6.0 KiB
Devicetree
251 lines
6.0 KiB
Devicetree
#include <dt-bindings/clock/qcom,rpmcc.h>
|
|
#include <dt-bindings/iio/qcom,spmi-vadc.h>
|
|
|
|
&blsp1_uart2 {
|
|
status = "ok"
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart_console_active>;
|
|
};
|
|
|
|
#include <dt-bindings/clock/qcom,gcc-sdm429w.h>
|
|
#include "qm215-camera-sensor-qrd.dtsi"
|
|
|
|
&pm8916_chg {
|
|
status = "ok"
|
|
qcom,chgr-led-support;
|
|
qcom,vddmax-mv = <4400>;
|
|
qcom,vddsafe-mv = <4400>;
|
|
qcom,batt-hot-percentage = <35>;
|
|
};
|
|
|
|
&pm8916_bms {
|
|
status = "ok"
|
|
qcom,battery-data = <&qrd_batterydata>;
|
|
qcom,batt-aging-comp;
|
|
qcom,resume-soc = <99>;
|
|
};
|
|
|
|
&pm8916_vib {
|
|
status = "ok"
|
|
};
|
|
|
|
&pm8916_vadc {
|
|
batt_therm {
|
|
qcom,scale-fn-type = <ADC_SCALE_BATT_THERM_QRD_215>;
|
|
};
|
|
};
|
|
|
|
&soc {
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
input-name = "gpio-keys";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&gpio_key_active>;
|
|
|
|
vol_up {
|
|
label = "volume_up";
|
|
gpios = <&tlmm 91 0x1>;
|
|
linux,input-type = <1>;
|
|
linux,code = <115>;
|
|
debounce-interval = <15>;
|
|
linux,can-disable;
|
|
gpio-key,wakeup;
|
|
};
|
|
};
|
|
|
|
fpc1020 {
|
|
compatible = "fpc,fpc1020";
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <48 0>;
|
|
fpc,gpio_rst = <&tlmm 124 0x0>;
|
|
fpc,gpio_irq = <&tlmm 48 0>;
|
|
vcc_spi-supply = <&pm8916_l5>;
|
|
vdd_io-supply = <&pm8916_l5>;
|
|
vdd_ana-supply = <&pm8916_l5>;
|
|
fpc,enable-on-boot;
|
|
pinctrl-names = "fpc1020_reset_reset",
|
|
"fpc1020_reset_active",
|
|
"fpc1020_irq_active";
|
|
pinctrl-0 = <&fpc_reset_low>;
|
|
pinctrl-1 = <&fpc_reset_high>;
|
|
pinctrl-2 = <&fpc_int_low>;
|
|
};
|
|
};
|
|
|
|
&sdhc_1 {
|
|
/* device core power supply */
|
|
vdd-supply = <&pm8916_l8>;
|
|
qcom,vdd-voltage-level = <2900000 2900000>;
|
|
qcom,vdd-current-level = <200 400000>;
|
|
|
|
/*
|
|
* device communication power is an external
|
|
* regulator eLDO3, which is enabled via L5A
|
|
*/
|
|
vdd-io-supply = <&pm8916_l5>;
|
|
qcom,vdd-io-always-on;
|
|
qcom,vdd-io-lpm-sup;
|
|
qcom,vdd-io-voltage-level = <1800000 1800000>;
|
|
qcom,vdd-io-current-level = <200 325000>;
|
|
|
|
pinctrl-names = "active", "sleep";
|
|
pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on &sdc1_rclk_on>;
|
|
pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off &sdc1_rclk_off>;
|
|
|
|
qcom,clk-rates = <400000 20000000 25000000 50000000 100000000 192000000
|
|
384000000>;
|
|
qcom,nonremovable;
|
|
qcom,bus-speed-mode = "HS400_1p8v", "HS200_1p8v", "DDR_1p8v";
|
|
|
|
status = "ok"
|
|
};
|
|
|
|
&sdhc_2 {
|
|
/* device core power supply */
|
|
vdd-supply = <&pm8916_l11>;
|
|
qcom,vdd-voltage-level = <2950000 2950000>;
|
|
qcom,vdd-current-level = <15000 800000>;
|
|
|
|
/* device communication power supply */
|
|
vdd-io-supply = <&pm8916_l12>;
|
|
qcom,vdd-io-voltage-level = <1800000 2950000>;
|
|
qcom,vdd-io-current-level = <200 22000>;
|
|
|
|
pinctrl-names = "active", "sleep";
|
|
pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
|
|
pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;
|
|
|
|
cd-gpios = <&tlmm 67 0x0>;
|
|
|
|
qcom,clk-rates = <400000 20000000 25000000 50000000 100000000
|
|
200000000>;
|
|
qcom,bus-speed-mode = "SDR12", "SDR25", "SDR50", "DDR50", "SDR104";
|
|
status = "ok"
|
|
};
|
|
|
|
&mdss_dsi_active {
|
|
mux {
|
|
pins = "gpio60", "gpio93", "gpio94";
|
|
function = "gpio";
|
|
};
|
|
|
|
config {
|
|
pins = "gpio60", "gpio93", "gpio94";
|
|
drive-strength = <8>; /* 8 mA */
|
|
bias-disable = <0>; /* no pull */
|
|
output-high;
|
|
};
|
|
};
|
|
|
|
&mdss_dsi_suspend {
|
|
mux {
|
|
pins = "gpio60", "gpio93", "gpio94";
|
|
function = "gpio";
|
|
};
|
|
|
|
config {
|
|
pins = "gpio60", "gpio93", "gpio94";
|
|
drive-strength = <2>; /* 2 mA */
|
|
bias-pull-down; /* pull down */
|
|
};
|
|
};
|
|
|
|
#include "msm8937-mdss-panels.dtsi"
|
|
|
|
&mdss_mdp {
|
|
qcom,mdss-pref-prim-intf = "dsi";
|
|
};
|
|
|
|
&dsi_panel_pwr_supply {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
qcom,panel-supply-entry@0 {
|
|
reg = <1>;
|
|
qcom,supply-name = "vddio";
|
|
qcom,supply-min-voltage = <1744000>;
|
|
qcom,supply-max-voltage = <1904000>;
|
|
qcom,supply-enable-load = <100000>;
|
|
qcom,supply-disable-load = <100>;
|
|
};
|
|
|
|
/delete-node/ qcom,panel-supply-entry@1;
|
|
/delete-node/ qcom,panel-supply-entry@2;
|
|
/delete-node/ qcom,panel-supply-entry@3;
|
|
};
|
|
|
|
&pm8916_gpios {
|
|
nfc_clk {
|
|
nfc_clk_default: nfc_clk_default {
|
|
pins = "gpio2";
|
|
function = "normal";
|
|
input-enable;
|
|
power-source = <1>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&i2c_5 { /* BLSP2 QUP1 (NFC) */
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
status = "ok"
|
|
nq@28 {
|
|
compatible = "qcom,nq-nci";
|
|
reg = <0x28>;
|
|
qcom,nq-irq = <&tlmm 17 0x00>;
|
|
qcom,nq-ven = <&tlmm 16 0x00>;
|
|
qcom,nq-firm = <&tlmm 130 0x00>;
|
|
qcom,nq-clkreq = <&pm8916_gpios 2 0x00>;
|
|
interrupt-parent = <&tlmm>;
|
|
qcom,clk-src = "BBCLK2";
|
|
interrupts = <17 0>;
|
|
interrupt-names = "nfc_irq";
|
|
pinctrl-names = "nfc_active", "nfc_suspend";
|
|
pinctrl-0 = <&nfc_int_active &nfc_disable_active
|
|
&nfc_clk_default>;
|
|
pinctrl-1 = <&nfc_int_suspend &nfc_disable_suspend>;
|
|
clocks = <&rpmcc RPM_SMD_BB_CLK2_PIN>;
|
|
clock-names = "ref_clk";
|
|
};
|
|
};
|
|
|
|
&mdss_dsi {
|
|
hw-config = "single_dsi";
|
|
};
|
|
|
|
&mdss_dsi0 {
|
|
qcom,dsi-pref-prim-pan = <&dsi_hx8399c_hd_vid>;
|
|
pinctrl-names = "mdss_default", "mdss_sleep";
|
|
pinctrl-0 = <&mdss_dsi_active &mdss_te_active>;
|
|
pinctrl-1 = <&mdss_dsi_suspend &mdss_te_suspend>;
|
|
|
|
qcom,platform-te-gpio = <&tlmm 24 0>;
|
|
qcom,platform-reset-gpio = <&tlmm 60 0>;
|
|
qcom,platform-bklight-en-gpio = <&tlmm 93 0>;
|
|
qcom,platform-enable-gpio = <&tlmm 94 0>;
|
|
};
|
|
|
|
&dsi_hx8399c_hd_vid {
|
|
qcom,mdss-dsi-panel-timings =
|
|
[e7 1c 12 00 42 42 18 20 17 03 04 00];
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
|
|
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_pwm";
|
|
qcom,mdss-dsi-bl-pmic-pwm-frequency = <100>;
|
|
qcom,mdss-dsi-bl-pmic-bank-select = <0>;
|
|
qcom,mdss-dsi-pwm-gpio = <&pm8916_mpps 4 0>;
|
|
qcom,esd-check-enabled;
|
|
qcom,mdss-dsi-panel-status-check-mode = "reg_read";
|
|
qcom,mdss-dsi-panel-status-command = [06 01 00 01 00 00 01 0a];
|
|
qcom,mdss-dsi-panel-status-command-state = "dsi_lp_mode";
|
|
qcom,mdss-dsi-panel-status-value = <0x9d 0x9d 0x9d 0x9d>;
|
|
qcom,mdss-dsi-panel-on-check-value = <0x9d 0x9d 0x9d 0x9d>;
|
|
qcom,mdss-dsi-panel-status-read-length = <4>;
|
|
qcom,mdss-dsi-panel-max-error-count = <3>;
|
|
qcom,mdss-dsi-min-refresh-rate = <48>;
|
|
qcom,mdss-dsi-max-refresh-rate = <60>;
|
|
qcom,mdss-dsi-pan-enable-dynamic-fps;
|
|
qcom,mdss-dsi-pan-fps-update =
|
|
"dfps_immediate_porch_mode_vfp";
|
|
};
|