Yuan Zhao
b8b16d992d
Since it was used only for dsi-hdmi bridge chipset, the chipset could not support higher rate, so set it to 100khz. Change-Id: If9a3f8ae2c89847caecb7c9dad52c0313edd3af1
136 lines
2.2 KiB
Devicetree
136 lines
2.2 KiB
Devicetree
#include "kona-qrd.dtsi"
|
|
|
|
&qupv3_se13_i2c {
|
|
status = "ok"
|
|
qcom,i2c-touch-active = "";
|
|
|
|
st_fts@49 {
|
|
st,x-flip;
|
|
st,y-flip;
|
|
};
|
|
};
|
|
|
|
&kona_snd {
|
|
qcom,msm-mbhc-usbc-audio-supported = <0>;
|
|
qcom,msm-mbhc-hphl-swh = <1>;
|
|
qcom,msm-mbhc-gnd-swh = <1>;
|
|
};
|
|
|
|
&redriver {
|
|
status = "disabled";
|
|
};
|
|
|
|
&usb1 {
|
|
qcom,ignore-wakeup-src-in-hostmode;
|
|
|
|
dwc3@a800000 {
|
|
dr_mode = "host";
|
|
};
|
|
};
|
|
|
|
&usb2_phy0 {
|
|
qcom,param-override-seq =
|
|
<0xc7 0x6c
|
|
0x03 0x70
|
|
0x03 0x74>;
|
|
};
|
|
|
|
&mdm0 {
|
|
status = "disabled";
|
|
};
|
|
|
|
&qupv3_se1_i2c {
|
|
status = "ok"
|
|
qcom,clk-freq-out = <100000>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
lt9611: lt,lt9611@2b {
|
|
compatible = "lt,lt9611uxc";
|
|
reg = <0x2b>;
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <1 0>;
|
|
interrupt-names = "lt_irq";
|
|
lt,irq-gpio = <&tlmm 1 0x0>;
|
|
lt,reset-gpio = <&tlmm 2 0x0>;
|
|
instance_id = <0>;
|
|
lt,non-pluggable;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <<9611_pins>;
|
|
|
|
lt,preferred-mode = "1920x1080";
|
|
|
|
lt,customize-modes {
|
|
lt,customize-mode-id@0 {
|
|
lt,mode-h-active = <1920>;
|
|
lt,mode-h-front-porch = <88>;
|
|
lt,mode-h-pulse-width = <44>;
|
|
lt,mode-h-back-porch = <148>;
|
|
lt,mode-h-active-high;
|
|
lt,mode-v-active = <1080>;
|
|
lt,mode-v-front-porch = <4>;
|
|
lt,mode-v-pulse-width = <5>;
|
|
lt,mode-v-back-porch = <36>;
|
|
lt,mode-v-active-high;
|
|
lt,mode-refresh-rate = <60>;
|
|
lt,mode-clock-in-khz = <148500>;
|
|
};
|
|
};
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
lt9611_in: endpoint {
|
|
remote-endpoint = <&ext_dsi_out>;
|
|
};
|
|
};
|
|
|
|
};
|
|
};
|
|
};
|
|
|
|
&sde_dsi {
|
|
qcom,dsi-default-panel = <&dsi_ext_bridge_1080p>;
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
ext_dsi_out: endpoint {
|
|
remote-endpoint = <<9611_in>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie2 {
|
|
qcom,boot-option = <0x0>;
|
|
};
|
|
|
|
&mhi_0 {
|
|
reg = <0x100 0x0 0x0 0x0 0x0>;
|
|
};
|
|
|
|
&pcie2_rp {
|
|
#address-cells = <5>;
|
|
#size-cells = <0>;
|
|
|
|
nvme: nvme {
|
|
reg = <0 0 0 0 0>;
|
|
qcom,iommu-group = <&nvme_pci_iommu_group>;
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
nvme_pci_iommu_group: nvme_pci_iommu_group {
|
|
qcom,iommu-dma-addr-pool = <0x20000000 0x40000000>;
|
|
qcom,iommu-dma = "fastmap";
|
|
};
|
|
};
|
|
};
|