xieqiong2
2f7ba2f3e9
Add intial charging and fg dtsi configuration for hawao. Change-Id: Ic0a08a0f29b3d6a9c85626ccd51352336d5e77d8 Signed-off-by: xieqiong2 <xieqiong2@lenovo.com> Reviewed-on: https://gerrit.mot.com/2140521 SME-Granted: SME Approvals Granted SLTApproved: Slta Waiver Tested-by: Jira Key Reviewed-by: Wang Wang <wangwang1@lenovo.com> Submit-Approved: Jira Key
106 lines
2.7 KiB
Devicetree
106 lines
2.7 KiB
Devicetree
/* Copyright (c) 2019, The Linux Foundation. All rights reserved.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 and
|
|
* only version 2 as published by the Free Software Foundation.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*/
|
|
|
|
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
|
#include "khaje-moto-common-overlay.dtsi"
|
|
#include "khaje-hawao-display.dtsi"
|
|
#include "khaje-hawao-fps-overlay_evb.dtsi"
|
|
#include "khaje-hawao-touchscreen-overlay.dtsi"
|
|
#include "khaje-hawao-nfc-overlay.dtsi"
|
|
#include "sgm7220.dtsi"
|
|
#include "discrete_charging_hawao.dtsi"
|
|
|
|
&firmware {
|
|
android {
|
|
vbmeta {
|
|
compatible = "android,vbmeta";
|
|
parts = "vbmeta,boot,system,vendor,dtbo";
|
|
};
|
|
};
|
|
};
|
|
&soc {
|
|
qcom,tz_gpio {
|
|
compatible = "qcom,tz_gpio";
|
|
tlmm-tz = <14>,
|
|
<15>,
|
|
<16>,
|
|
<17>;
|
|
};
|
|
|
|
ext_vib {
|
|
compatible = "ext-vibrator-ldo";
|
|
vib-gpio-vcc-enable;
|
|
vib,gpio_2v6_en = <&tlmm 25 0x00>;
|
|
vib,gpio_3v0_en = <&tlmm 97 0x00>;
|
|
};
|
|
};
|
|
|
|
|
|
&tlmm{
|
|
capsense_sar_gpio_pins: capsense_sar_gpio_pins {
|
|
mux {
|
|
pins = "gpio106";
|
|
function = "gpio";
|
|
};
|
|
|
|
config {
|
|
pins = "gpio106";
|
|
drive-strength = <2>;
|
|
bias-pull-up;
|
|
input-enable;
|
|
};
|
|
};
|
|
};
|
|
|
|
|
|
&sdhc_2 {
|
|
vdd-supply = <&L22A>;
|
|
qcom,vdd-voltage-level = <2960000 2960000>;
|
|
qcom,vdd-current-level = <0 800000>;
|
|
|
|
vdd-io-supply = <&L5A>;
|
|
qcom,vdd-io-voltage-level = <1800000 2960000>;
|
|
qcom,vdd-io-current-level = <0 22000>;
|
|
|
|
vdd-io-bias-supply = <&L7A>;
|
|
qcom,vdd-io-bias-voltage-level = <1256000 1256000>;
|
|
qcom,vdd-io-bias-current-level = <0 6000>;
|
|
|
|
pinctrl-names = "active", "sleep";
|
|
pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
|
|
pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
|
|
|
|
cd-gpios = <&tlmm 88 GPIO_ACTIVE_HIGH>;
|
|
|
|
status = "ok"
|
|
};
|
|
|
|
&qupv3_se0_i2c {
|
|
status = "ok"
|
|
aw9610x_sar@12 {
|
|
compatible = "awinic,aw9610x_sar_0";
|
|
reg = <0x12>;
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <106 0x02>;
|
|
irq-gpio = <&tlmm 106 0x02>;
|
|
chip_name = "AW96105";
|
|
sar-num = <0>;
|
|
cap_vcc-supply = <&pm6125_l21>;
|
|
aw9610x,channel_number = <0x3>;
|
|
ch0_name = "capsense_bottom_left";
|
|
ch1_name = "capsense_top";
|
|
ch2_name = "capsense_bottom_right";
|
|
aw9610x,using-firmware;
|
|
aw9610x,firmware_name = "aw9610x_0";
|
|
};
|
|
};
|