Gopala Krishna Nuthaki
6214d18889
Update battery mitigation levels to 10A to support both 10A and 8A variant QRD devices. Change-Id: I2960ff8b6acfe4631f6ff85f2804df103a667c7b
577 lines
14 KiB
Devicetree
577 lines
14 KiB
Devicetree
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/linux-event-codes.h>
|
|
#include <dt-bindings/iio/qcom,spmi-vadc.h>
|
|
#include "lagoon-audio-overlay.dtsi"
|
|
#include "lagoon-sde-display.dtsi"
|
|
#include "camera/lagoon-camera-sensor-mtp.dtsi"
|
|
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
|
|
#include "lagoon-thermal-overlay.dtsi"
|
|
|
|
&soc {
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
label = "gpio-keys";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&key_vol_up_default>;
|
|
|
|
vol_up {
|
|
label = "volume_up";
|
|
gpios = <&pm6350_gpios 2 GPIO_ACTIVE_LOW>;
|
|
linux,input-type = <1>;
|
|
linux,code = <KEY_VOLUMEUP>;
|
|
gpio-key,wakeup;
|
|
debounce-interval = <15>;
|
|
linux,can-disable;
|
|
};
|
|
};
|
|
|
|
qrd_batterydata: qcom,battery-data {
|
|
qcom,batt-id-range-pct = <15>;
|
|
#include "qg-batterydata-atl436186020H_3780mAh.dtsi"
|
|
#include "qg-batterydata-atl466271_3300mAh.dtsi"
|
|
};
|
|
};
|
|
|
|
&pm6150a_l1 {
|
|
qcom,init-voltage = <1800000>;
|
|
};
|
|
|
|
&pm6350_gpios {
|
|
key_vol_up {
|
|
key_vol_up_default: key_vol_up_default {
|
|
pins = "gpio2";
|
|
function = "normal";
|
|
input-enable;
|
|
bias-pull-up;
|
|
power-source = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&ufsphy_mem {
|
|
compatible = "qcom,ufs-phy-qmp-v3";
|
|
|
|
vdda-phy-supply = <&L18A>;
|
|
vdda-pll-supply = <&L22A>;
|
|
vdda-phy-max-microamp = <62900>;
|
|
vdda-pll-max-microamp = <18300>;
|
|
|
|
status = "ok"
|
|
};
|
|
|
|
&ufshc_mem {
|
|
vdd-hba-supply = <&gcc_ufs_phy_gdsc>;
|
|
vdd-hba-fixed-regulator;
|
|
vcc-supply = <&L7E>;
|
|
vcc-voltage-level = <2950000 2960000>;
|
|
vccq2-supply = <&L12A>;
|
|
vccq2-voltage-level = <1800000 1800000>;
|
|
vcc-max-microamp = <800000>;
|
|
vccq2-min-microamp = <0>;
|
|
vccq2-max-microamp = <800000>;
|
|
vccq2-pwr-collapse-sup;
|
|
|
|
qcom,vddp-ref-clk-supply = <&L22A>;
|
|
qcom,vddp-ref-clk-max-microamp = <100>;
|
|
qcom,vddp-ref-clk-min-uV = <1152000>;
|
|
qcom,vddp-ref-clk-max-uV = <1200000>;
|
|
status = "ok"
|
|
};
|
|
|
|
&sdhc_1 {
|
|
vdd-supply = <&L7E>;
|
|
qcom,vdd-voltage-level = <2960000 2960000>;
|
|
qcom,vdd-current-level = <0 570000>;
|
|
|
|
vdd-io-supply = <&L12A>;
|
|
qcom,vdd-io-always-on;
|
|
qcom,vdd-io-lpm-sup;
|
|
qcom,vdd-io-voltage-level = <1800000 1800000>;
|
|
qcom,vdd-io-current-level = <0 325000>;
|
|
|
|
pinctrl-names = "active", "sleep";
|
|
pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on
|
|
&sdc1_rclk_on>;
|
|
pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off
|
|
&sdc1_rclk_off>;
|
|
|
|
status = "ok"
|
|
};
|
|
|
|
&sdhc_2 {
|
|
vdd-supply = <&L9E>;
|
|
qcom,vdd-voltage-level = <2960000 2960000>;
|
|
qcom,vdd-current-level = <0 800000>;
|
|
|
|
vdd-io-supply = <&L6E>;
|
|
qcom,vdd-io-voltage-level = <1800000 2950000>;
|
|
qcom,vdd-io-current-level = <0 22000>;
|
|
|
|
pinctrl-names = "active", "sleep";
|
|
pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
|
|
pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
|
|
|
|
cd-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
|
|
|
|
status = "ok"
|
|
};
|
|
|
|
&pm6150a_amoled {
|
|
status = "ok"
|
|
};
|
|
|
|
&dsi_r66451_amoled_60hz_video {
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
|
|
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
|
qcom,mdss-dsi-bl-min-level = <1>;
|
|
qcom,mdss-dsi-bl-max-level = <255>;
|
|
qcom,mdss-dsi-bl-max-level = <4095>;
|
|
qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
|
|
};
|
|
|
|
&dsi_r66451_amoled_90hz_video {
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
|
|
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
|
qcom,mdss-dsi-bl-min-level = <1>;
|
|
qcom,mdss-dsi-bl-max-level = <255>;
|
|
qcom,mdss-dsi-bl-max-level = <4095>;
|
|
qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
|
|
};
|
|
|
|
&dsi_r66451_amoled_120hz_video {
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
|
|
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
|
qcom,mdss-dsi-bl-min-level = <1>;
|
|
qcom,mdss-dsi-bl-max-level = <255>;
|
|
qcom,mdss-dsi-bl-inverted-dbv;
|
|
qcom,mdss-dsi-bl-max-level = <4095>;
|
|
qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
|
|
};
|
|
|
|
&dsi_r66451_amoled_60hz_cmd {
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
|
|
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
|
qcom,mdss-dsi-bl-min-level = <1>;
|
|
qcom,mdss-dsi-bl-max-level = <255>;
|
|
qcom,mdss-dsi-bl-max-level = <4095>;
|
|
qcom,platform-te-gpio = <&tlmm 23 0>;
|
|
qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
|
|
};
|
|
|
|
&dsi_r66451_amoled_90hz_cmd {
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
|
|
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
|
qcom,mdss-dsi-bl-min-level = <1>;
|
|
qcom,mdss-dsi-bl-max-level = <255>;
|
|
qcom,mdss-dsi-bl-max-level = <4095>;
|
|
qcom,platform-te-gpio = <&tlmm 23 0>;
|
|
qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
|
|
};
|
|
|
|
&dsi_r66451_amoled_120hz_cmd {
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
|
|
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
|
qcom,mdss-dsi-bl-min-level = <1>;
|
|
qcom,mdss-dsi-bl-max-level = <255>;
|
|
qcom,mdss-dsi-bl-max-level = <4095>;
|
|
qcom,mdss-dsi-bl-inverted-dbv;
|
|
qcom,platform-te-gpio = <&tlmm 23 0>;
|
|
qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
|
|
};
|
|
|
|
&sde_dsi {
|
|
qcom,dsi-default-panel = <&dsi_r66451_amoled_120hz_video>;
|
|
};
|
|
|
|
&qupv3_se0_i2c {
|
|
status = "ok"
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
nq@28 {
|
|
compatible = "qcom,nq-nci";
|
|
reg = <0x28>;
|
|
qcom,nq-irq = <&tlmm 9 0x00>;
|
|
qcom,nq-ven = <&tlmm 6 0x00>;
|
|
qcom,nq-firm = <&tlmm 8 0x00>;
|
|
qcom,nq-clkreq = <&tlmm 7 0x00>;
|
|
qcom,nq-vdd-1p8-supply = <&L11A>;
|
|
qcom,nq-vdd-1p8-voltage = <1800000 1800000>;
|
|
qcom,nq-vdd-1p8-current = <157000>;
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <9 0>;
|
|
interrupt-names = "nfc_irq";
|
|
pinctrl-names = "nfc_active", "nfc_suspend";
|
|
pinctrl-0 = <&nfc_int_active &nfc_enable_active
|
|
&nfc_clk_req_active>;
|
|
pinctrl-1 = <&nfc_int_suspend &nfc_enable_suspend
|
|
&nfc_clk_req_suspend>;
|
|
};
|
|
};
|
|
|
|
&pm7250b_charger {
|
|
status = "ok"
|
|
io-channels = <&pm7250b_vadc ADC_USB_IN_V_16>,
|
|
<&pm7250b_vadc ADC_USB_IN_I>,
|
|
<&pm7250b_vadc ADC_CHG_TEMP>,
|
|
<&pm7250b_vadc ADC_DIE_TEMP>,
|
|
<&pm7250b_vadc ADC_AMUX_THM3_PU2>,
|
|
<&pm7250b_vadc ADC_SBUx>,
|
|
<&pm7250b_vadc ADC_VPH_PWR>,
|
|
<&pm7250b_vadc ADC_AMUX_THM1_PU2>;
|
|
io-channel-names = "usb_in_voltage",
|
|
"usb_in_current",
|
|
"chg_temp",
|
|
"die_temp",
|
|
"conn_temp",
|
|
"sbux_res",
|
|
"vph_voltage",
|
|
"skin_temp";
|
|
qcom,battery-data = <&qrd_batterydata>;
|
|
qcom,sec-charger-config = <1>;
|
|
qcom,auto-recharge-soc = <98>;
|
|
qcom,step-charging-enable;
|
|
qcom,sw-jeita-enable;
|
|
qcom,charger-temp-max = <800>;
|
|
qcom,smb-temp-max = <800>;
|
|
qcom,suspend-input-on-debug-batt;
|
|
qcom,fcc-stepping-enable;
|
|
qcom,fcc-step-delay-ms = <100>;
|
|
qcom,fcc-step-size-ua = <100000>;
|
|
qcom,smb-internal-pull-kohm = <0>;
|
|
qcom,en-skin-therm-mitigation;
|
|
qcom,thermal-mitigation = <10000000 9500000 9000000 8500000 8000000
|
|
7500000 7000000 6500000 6000000 5500000 5000000 4500000
|
|
4000000 3500000 3000000 2500000 2000000 1500000 1000000
|
|
500000>;
|
|
};
|
|
|
|
&pm7250b_qg {
|
|
status = "ok"
|
|
io-channels = <&pm7250b_vadc ADC_BAT_THERM_PU2>,
|
|
<&pm7250b_vadc ADC_BAT_ID_PU2>;
|
|
io-channel-names = "batt-therm",
|
|
"batt-id";
|
|
qcom,qg-iterm-ma = <150>;
|
|
qcom,hold-soc-while-full;
|
|
qcom,linearize-soc;
|
|
qcom,cl-feedback-on;
|
|
qcom,tcss-enable;
|
|
qcom,fvss-enable;
|
|
qcom,fvss-vbatt-mv = <3300>;
|
|
qcom,bass-enable;
|
|
qcom,use-cp-iin-sns;
|
|
};
|
|
|
|
&wcd937x_codec {
|
|
status = "ok"
|
|
};
|
|
|
|
&wcd938x_codec {
|
|
status = "disabled";
|
|
};
|
|
|
|
&wcd937x_rx_slave {
|
|
status = "ok"
|
|
};
|
|
|
|
&wcd937x_tx_slave {
|
|
status = "ok"
|
|
};
|
|
|
|
&wcd938x_tx_slave {
|
|
status = "disabled";
|
|
};
|
|
|
|
&wcd938x_rx_slave {
|
|
status = "disabled";
|
|
};
|
|
|
|
&lagoon_snd {
|
|
qcom,model = "lito-lagoonqrd-snd-card";
|
|
qcom,msm-mi2s-master = <1>, <1>, <1>, <1>, <1>, <1>;
|
|
qcom,wcn-btfm = <1>;
|
|
qcom,audio-routing =
|
|
"AMIC1", "MIC BIAS1",
|
|
"MIC BIAS1", "Analog Mic1",
|
|
"AMIC2", "MIC BIAS2",
|
|
"MIC BIAS2", "Analog Mic2",
|
|
"AMIC3", "MIC BIAS3",
|
|
"MIC BIAS3", "Analog Mic3",
|
|
"AMIC4", "MIC BIAS1",
|
|
"MIC BIAS1", "Analog Mic4",
|
|
"TX DMIC0", "MIC BIAS3",
|
|
"MIC BIAS3", "Digital Mic0",
|
|
"TX DMIC1", "MIC BIAS3",
|
|
"MIC BIAS3", "Digital Mic1",
|
|
"TX DMIC2", "MIC BIAS1",
|
|
"MIC BIAS1", "Digital Mic2",
|
|
"TX DMIC3", "MIC BIAS1",
|
|
"MIC BIAS1", "Digital Mic3",
|
|
"TX DMIC4", "MIC BIAS4",
|
|
"MIC BIAS4", "Digital Mic4",
|
|
"TX DMIC5", "MIC BIAS4",
|
|
"MIC BIAS4", "Digital Mic5",
|
|
"IN1_HPHL", "HPHL_OUT",
|
|
"IN2_HPHR", "HPHR_OUT",
|
|
"IN3_AUX", "AUX_OUT",
|
|
"TX SWR_ADC0", "ADC1_OUTPUT",
|
|
"TX SWR_ADC2", "ADC2_OUTPUT",
|
|
"TX SWR_ADC3", "ADC3_OUTPUT",
|
|
"TX SWR_DMIC0", "DMIC1_OUTPUT",
|
|
"TX SWR_DMIC1", "DMIC2_OUTPUT",
|
|
"TX SWR_DMIC2", "DMIC3_OUTPUT",
|
|
"TX SWR_DMIC3", "DMIC4_OUTPUT",
|
|
"TX SWR_DMIC4", "DMIC5_OUTPUT",
|
|
"TX SWR_DMIC5", "DMIC6_OUTPUT",
|
|
"TX SWR_DMIC6", "DMIC7_OUTPUT",
|
|
"TX SWR_DMIC7", "DMIC8_OUTPUT",
|
|
"WSA SRC0_INP", "SRC0",
|
|
"WSA_TX DEC0_INP", "TX DEC0 MUX",
|
|
"WSA_TX DEC1_INP", "TX DEC1 MUX",
|
|
"RX_TX DEC0_INP", "TX DEC0 MUX",
|
|
"RX_TX DEC1_INP", "TX DEC1 MUX",
|
|
"RX_TX DEC2_INP", "TX DEC2 MUX",
|
|
"RX_TX DEC3_INP", "TX DEC3 MUX",
|
|
"SpkrLeft IN", "WSA_SPK1 OUT",
|
|
"VA_AIF1 CAP", "VA_SWR_CLK",
|
|
"VA_AIF2 CAP", "VA_SWR_CLK",
|
|
"VA_AIF3 CAP", "VA_SWR_CLK",
|
|
"VA MIC BIAS3", "Digital Mic0",
|
|
"VA MIC BIAS3", "Digital Mic1",
|
|
"VA MIC BIAS1", "Digital Mic2",
|
|
"VA MIC BIAS1", "Digital Mic3",
|
|
"VA MIC BIAS4", "Digital Mic4",
|
|
"VA MIC BIAS4", "Digital Mic5",
|
|
"VA DMIC0", "VA MIC BIAS3",
|
|
"VA DMIC1", "VA MIC BIAS3",
|
|
"VA DMIC2", "VA MIC BIAS1",
|
|
"VA DMIC3", "VA MIC BIAS1",
|
|
"VA DMIC4", "VA MIC BIAS4",
|
|
"VA DMIC5", "VA MIC BIAS4",
|
|
"VA SWR_ADC0", "VA_SWR_CLK",
|
|
"VA SWR_ADC1", "VA_SWR_CLK",
|
|
"VA SWR_ADC2", "VA_SWR_CLK",
|
|
"VA SWR_ADC3", "VA_SWR_CLK",
|
|
"VA SWR_MIC0", "VA_SWR_CLK",
|
|
"VA SWR_MIC1", "VA_SWR_CLK",
|
|
"VA SWR_MIC2", "VA_SWR_CLK",
|
|
"VA SWR_MIC3", "VA_SWR_CLK",
|
|
"VA SWR_MIC4", "VA_SWR_CLK",
|
|
"VA SWR_MIC5", "VA_SWR_CLK",
|
|
"VA SWR_MIC6", "VA_SWR_CLK",
|
|
"VA SWR_MIC7", "VA_SWR_CLK",
|
|
"VA SWR_ADC0", "ADC1_OUTPUT",
|
|
"VA SWR_ADC2", "ADC2_OUTPUT",
|
|
"VA SWR_ADC3", "ADC3_OUTPUT",
|
|
"VA SWR_MIC0", "DMIC1_OUTPUT",
|
|
"VA SWR_MIC1", "DMIC2_OUTPUT",
|
|
"VA SWR_MIC2", "DMIC3_OUTPUT",
|
|
"VA SWR_MIC3", "DMIC4_OUTPUT",
|
|
"VA SWR_MIC4", "DMIC5_OUTPUT",
|
|
"VA SWR_MIC5", "DMIC6_OUTPUT",
|
|
"VA SWR_MIC6", "DMIC7_OUTPUT",
|
|
"VA SWR_MIC7", "DMIC8_OUTPUT";
|
|
qcom,msm-mbhc-hphl-swh = <0>;
|
|
qcom,msm-mbhc-gnd-swh = <0>;
|
|
qcom,wsa-max-devs = <1>;
|
|
qcom,wsa-devs = <&wsa883x_0221>;
|
|
qcom,wsa-aux-dev-prefix = "SpkrLeft";
|
|
qcom,codec-max-aux-devs = <1>;
|
|
qcom,msm-mbhc-usbc-audio-supported = <1>;
|
|
qcom,codec-aux-devs = <&wcd937x_codec>;
|
|
qcom,msm_audio_ssr_devs = <&audio_apr>, <&q6core>,
|
|
<&lpi_tlmm>, <&bolero>;
|
|
};
|
|
|
|
&qupv3_se8_i2c {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
status = "ok"
|
|
qcom,i2c-touch-active = "focaltech,fts_ts";
|
|
|
|
focaltech@38 {
|
|
compatible = "focaltech,fts_ts";
|
|
reg = <0x38>;
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <22 0x2008>;
|
|
focaltech,reset-gpio = <&tlmm 21 0x00>;
|
|
focaltech,irq-gpio = <&tlmm 22 0x2008>;
|
|
focaltech,max-touch-number = <5>;
|
|
focaltech,display-coords = <0 0 1080 2340>;
|
|
|
|
vdd-supply = <&L6A>;
|
|
|
|
pinctrl-names = "pmx_ts_active", "pmx_ts_suspend","pmx_ts_release";
|
|
pinctrl-0 = <&ts_active>;
|
|
pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
|
|
pinctrl-2 = <&pmx_ts_release>;
|
|
|
|
panel = <&dsi_r66451_amoled_60hz_cmd
|
|
&dsi_r66451_amoled_90hz_cmd
|
|
&dsi_r66451_amoled_120hz_cmd
|
|
&dsi_r66451_amoled_60hz_video
|
|
&dsi_r66451_amoled_90hz_video
|
|
&dsi_r66451_amoled_120hz_video>;
|
|
};
|
|
};
|
|
|
|
&pm7250b_vadc {
|
|
smb1390_therm@e {
|
|
qcom,scale-fn-type = <ADC_SCALE_HW_CALIB_PM5_SMB1398_TEMP>;
|
|
};
|
|
};
|
|
|
|
&pm7250b_gpios {
|
|
smb_stat {
|
|
smb_stat_default: smb_stat_default {
|
|
pins = "gpio6";
|
|
function = "normal";
|
|
input-enable;
|
|
bias-pull-up;
|
|
qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
|
|
power-source = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&qupv3_se10_i2c {
|
|
qcom,clk-freq-out = <100000>;
|
|
status = "ok"
|
|
#include "smb1398.dtsi"
|
|
};
|
|
|
|
&smb1396 {
|
|
interrupts = <0x2 0xc5 0x0 IRQ_TYPE_LEVEL_LOW>;
|
|
interrupt-parent = <&spmi_bus>;
|
|
interrupt-names = "smb1396";
|
|
pinctrl-names = "default";
|
|
qcom,enable-toggle-stat;
|
|
pinctrl-0 = <&smb_stat_default>;
|
|
status = "ok"
|
|
};
|
|
|
|
&smb1396_div2_cp_master {
|
|
io-channels = <&pm7250b_vadc ADC_AMUX_THM2>;
|
|
qcom,parallel-input-mode = <1>; /* USBIN */
|
|
qcom,parallel-output-mode = <2>; /* VBAT */
|
|
qcom,div2-cp-min-ilim-ua = <750000>;
|
|
status = "ok"
|
|
};
|
|
|
|
&smb1396_slave {
|
|
status = "ok"
|
|
};
|
|
|
|
&smb1396_div2_cp_slave {
|
|
status = "ok"
|
|
};
|
|
|
|
&qusb_phy0 {
|
|
qcom,qusb-phy-init-seq =
|
|
/* <value reg_offset> */
|
|
<0x23 0x210 /* PWR_CTRL1 */
|
|
0x03 0x04 /* PLL_ANALOG_CONTROLS_TWO */
|
|
0x7c 0x18c /* PLL_CLOCK_INVERTERS */
|
|
0x80 0x2c /* PLL_CMODE */
|
|
0x0a 0x184 /* PLL_LOCK_DELAY */
|
|
0x19 0xb4 /* PLL_DIGITAL_TIMERS_TWO */
|
|
0x40 0x194 /* PLL_BIAS_CONTROL_1 */
|
|
0x16 0x198 /* PLL_BIAS_CONTROL_2 */
|
|
0x21 0x214 /* PWR_CTRL2 */
|
|
0x08 0x220 /* IMP_CTRL1 */
|
|
0x58 0x224 /* IMP_CTRL2 */
|
|
0x47 0x240 /* TUNE1 */
|
|
0x29 0x244 /* TUNE2 */
|
|
0xca 0x248 /* TUNE3 */
|
|
0x04 0x24c /* TUNE4 */
|
|
0x03 0x250 /* TUNE5 */
|
|
0x30 0x23c /* CHG_CTRL2 */
|
|
0x22 0x210>; /* PWR_CTRL1 */
|
|
|
|
qcom,qusb-phy-host-init-seq =
|
|
/* <value reg_offset> */
|
|
<0x23 0x210 /* PWR_CTRL1 */
|
|
0x03 0x04 /* PLL_ANALOG_CONTROLS_TWO */
|
|
0x7c 0x18c /* PLL_CLOCK_INVERTERS */
|
|
0x80 0x2c /* PLL_CMODE */
|
|
0x0a 0x184 /* PLL_LOCK_DELAY */
|
|
0x19 0xb4 /* PLL_DIGITAL_TIMERS_TWO */
|
|
0x40 0x194 /* PLL_BIAS_CONTROL_1 */
|
|
0x16 0x198 /* PLL_BIAS_CONTROL_2 */
|
|
0x21 0x214 /* PWR_CTRL2 */
|
|
0x08 0x220 /* IMP_CTRL1 */
|
|
0x58 0x224 /* IMP_CTRL2 */
|
|
0x47 0x240 /* TUNE1 */
|
|
0x29 0x244 /* TUNE2 */
|
|
0xca 0x248 /* TUNE3 */
|
|
0x04 0x24c /* TUNE4 */
|
|
0x03 0x250 /* TUNE5 */
|
|
0x30 0x23c /* CHG_CTRL2 */
|
|
0x22 0x210>; /* PWR_CTRL1 */
|
|
};
|
|
|
|
&tlmm {
|
|
fpc_reset_int: fpc_reset_int {
|
|
fpc_reset_low: reset_low {
|
|
mux {
|
|
pins = "gpio18";
|
|
function = "gpio";
|
|
};
|
|
|
|
config {
|
|
pins = "gpio18";
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
output-low;
|
|
};
|
|
};
|
|
|
|
fpc_reset_high: reset_high {
|
|
mux {
|
|
pins = "gpio18";
|
|
function = "gpio";
|
|
};
|
|
|
|
config {
|
|
pins = "gpio18";
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
output-high;
|
|
};
|
|
};
|
|
|
|
fpc_int_low: int_low {
|
|
mux {
|
|
pins = "gpio17";
|
|
function = "gpio";
|
|
};
|
|
|
|
config {
|
|
pins = "gpio17";
|
|
drive-strength = <2>;
|
|
bias-pull-down;
|
|
input-enable;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&soc {
|
|
fingerprint: fpc1020 {
|
|
compatible = "fpc,fpc1020";
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <17 0>;
|
|
fpc,gpio_rst = <&tlmm 18 0>;
|
|
fpc,gpio_irq = <&tlmm 17 0>;
|
|
fpc,enable-on-boot;
|
|
pinctrl-names = "fpc1020_reset_reset",
|
|
"fpc1020_reset_active",
|
|
"fpc1020_irq_active";
|
|
pinctrl-0 = <&fpc_reset_low>;
|
|
pinctrl-1 = <&fpc_reset_high>;
|
|
pinctrl-2 = <&fpc_int_low>;
|
|
};
|
|
};
|