TP:
When sending multiple commands at the same time, the ack signal of
unexpected commands may be read, resulting in command sending errors.
Change-Id: I6f222a20725f5adc1509a01bd29f972c3171e56d
Reviewed-on: https://gerrit.mot.com/2178632
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Jianqi Yang <yangj@motorola.com>
Submit-Approved: Jira Key
Modify:
- Add the configuration for txd ili7807s.
- Change the ic name to ilitek_txd for CQA test.
Change-Id: I61ebc4ea91dbb0e016589ff3938a31f727514144
Reviewed-on: https://gerrit.mot.com/2176648
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Yeqing Wang <wangyq13@motorola.com>
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
TP:
1. Open the esd check function,when the touch IC dies, it can be
restored to normal by hardware reset.
2. Increase the delay between the stylus command and the clock to
prevent the IC from hanging up.
Change-Id: I20617d63c0d53d60d1100b9eb26182096c657b16
Reviewed-on: https://gerrit.mot.com/2164520
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Jichao Zou <zoujc@motorola.com>
Submit-Approved: Jira Key
TP:
When the screen is off, the TP driver starts to read gesture events
after receiving the interrupt.But I2C bus is still in the suspended
state, so gesture events cannot be read out.
geni_i2c_xfer System suspended
[GTP-INF][goodix_i2c_read:82] I2c read retry[1]:0x10308
geni_i2c_xfer System suspended
[GTP-INF][goodix_i2c_read:82] I2c read retry[2]:0x10308
[GTP-ERR][goodix_i2c_read:87] I2c read failed,dev:5d,reg:10308,size:26
[GTP-ERR][gsx_gesture_ist:236] failed get gesture data
Change-Id: If3ebbc4b65829def142835c51816b70e0a474865
Reviewed-on: https://gerrit.mot.com/2158726
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Jichao Zou <zoujc@motorola.com>
Submit-Approved: Jira Key
1. Update FOD gesture trigger in screen off mode.
2. Add FOD event support in screen on mode
Change-Id: I7ecbfdb4aff8eaf34e88247d91d08279edd018a6
Signed-off-by: Yan Zhang <zhangy26@motorola.com>
Reviewed-on: https://gerrit.mot.com/2152070
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Wei Deng <dengwei1@motorola.com>
Reviewed-by: Xiangpo Zhao <zhaoxp3@motorola.com>
Submit-Approved: Jira Key
TP:
When exiting the stylus mode, the IC will send an abnormal reset
interrupt. At this time, the stylus will be enabled again,
but because the stylus clock is closed, the touch will not work.
Change-Id: Id1b393de2b2bee5b06e9d4f5b74dfd301be4547d
Reviewed-on: https://gerrit.mot.com/2150837
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Jichao Zou <zoujc@motorola.com>
Submit-Approved: Jira Key
TP:
Record the value of the received mode from system and the value
successfully set to the touch IC.
Change-Id: Ie10f25be6d0d9fe9d21cf385a626496cc9aedfa5
Reviewed-on: https://gerrit.mot.com/2144916
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Jichao Zou <zoujc@motorola.com>
Submit-Approved: Jira Key
TP:
Support film sensitivity function in RoguePRC project.
Change-Id: I830adb55e9b9b93aef6dc90d757ef9eaf206a2cb
Reviewed-on: https://gerrit.mot.com/2134201
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Jichao Zou <zoujc@motorola.com>
Submit-Approved: Jira Key
1. If the interpolation mode is disabled, the report rate is the
default 240Hz(Hiphic) or 360Hz(Hiphi)
2. If the interpolation is enabled and the refresh
rate is 144Hz, the reporting rate is 576Hz(Hiphic) 720Hz(Hiphi)
3. At other refresh rate, if the interpolation mode is enabled, the
report rate is 480Hz(Hiphic) 720Hz(Hiphi).
Change-Id: Ibcd6ba61457e5e5f6fd32a6583f5bdcada531fc5
Reviewed-on: https://gerrit.mot.com/2134669
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Jichao Zou <zoujc@motorola.com>
Submit-Approved: Jira Key
Goodix IC requires device confirm within 50ms after power on.
If this time exceeds 50ms, the i2c firmware will colse the
spi channel, and the spi firmware will close the i2c channel.
Change-Id: I178cea55e280ffb53fca444cdd8ed32905a928c5
Reviewed-on: https://gerrit.mot.com/2133988
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Jianqi Yang <yangj@motorola.com>
Submit-Approved: Jira Key
When entering the deepsleep state, touch IC will power off,
so there is no need to send the suspend command.
Change-Id: I6b6a3b29eb3b1acee6c72db2b97fdb90710f25bc
Reviewed-on: https://gerrit.mot.com/2134059
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Jianqi Yang <yangj@motorola.com>
Submit-Approved: Jira Key
- Check if panel is available, if not, don't probe, save boot time
- Set avdd to 3v, same as other touch driver.
Change-Id: I34711276c2e5efcf1acc9421db2e347d95f2b41b
Signed-off-by: wangyq13 <wangyq13@lenovo.com>
Reviewed-on: https://gerrit.mot.com/2131131
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Jun Weng <wengjun1@motorola.com>
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
request pm_qos during the interrupt processing to prevent
the CPU from going to sleep state.
Change-Id: I95728329c7df7a4376415b9d8ec20d6525fe45c8
Reviewed-on: https://gerrit.mot.com/2124280
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Reviewed-by: Jichao Zou <zoujc@motorola.com>
Tested-by: Jira Key
Submit-Approved: Jira Key
TP:
If the noise detection fails after calibration, the touch IC will
report the "F3 E0" event, and when the event is received,
the touch driver will send the calibration command again.
Change-Id: Ifd2f4bd287fbdc7861a127d2ffd481f635d963c7
Reviewed-on: https://gerrit.mot.com/2123149
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Jichao Zou <zoujc@motorola.com>
Submit-Approved: Jira Key
request pm_qos during the interrupt processing to prevent
the CPU from going to sleep state.
Change-Id: I78a67ef1aa9a363e9d7f9546b8d4c20a81ac04c4
Reviewed-on: https://gerrit.mot.com/2107618
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Jichao Zou <zoujc@motorola.com>
Submit-Approved: Jira Key
TP:
Support Pmk8350 gpio3 as the stylus clock for Rogue PVT, and the
output frequency is 19.2Mhz.
Change-Id: I5dae054b6170b921b7afee1853b7de7995531705
Reviewed-on: https://gerrit.mot.com/2111742
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Jianqi Yang <yangj@motorola.com>
Submit-Approved: Jira Key
TP:
Since the sensitivity node is a general node in the framework,
the judgment of the mode value is increased.
Change-Id: I82d2727e8ebd60c96c13edf2dd923630dc828290
Reviewed-on: https://gerrit.mot.com/2116173
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Jichao Zou <zoujc@motorola.com>
Submit-Approved: Jira Key
1. Add the function of leather mode in the
univeral interface sensitivity.
2. The mode setting instructions are as follows:
mode = 0x00/0x01 Exit/Enter film sensitivity mode.
mode = 0x10/0x11 Exit/Enter leahter sensitivity mode
Change-Id: I35d49aaf225e8b941a4f2552a2ccd9d33a34dd92
Reviewed-on: https://gerrit.mot.com/2113437
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Jun Weng <wengjun1@motorola.com>
Reviewed-by: Jichao Zou <zoujc@motorola.com>
Submit-Approved: Jira Key
1. Close the stylus clock when system suspend and the stylus
mode exits.
2. Add 16ms delay between each command.
Change-Id: I6dff47410315272167d47a733b1058736f72c737
Reviewed-on: https://gerrit.mot.com/2108295
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Jichao Zou <zoujc@motorola.com>
Submit-Approved: Jira Key
zhuwg1