devon:charger bring up
charger bring up change dtsi for charger bring up Change-Id: If62350beb67b7b42a0d4a3639511b4c2d4cface0 Signed-off-by: longc102 <longc102@motorola.com> Reviewed-on: https://gerrit.mot.com/2208806 SME-Granted: SME Approvals Granted SLTApproved: Slta Waiver Submit-Approved: Jira Key Tested-by: Jira Key Reviewed-by: Qiong Xie <xieq2@motorola.com> Reviewed-on: https://gerrit.mot.com/2221192 Reviewed-by: Jianguo Liu <liujg6@motorola.com> Reviewed-by: Wang Wang <wangwang1@lenovo.com>
This commit is contained in:
longc102 authored and Carlos Pinho committed
1 parent
d793756686
commit
e5bf1dfd0f
3 files changed
+74
-137
No files matched your search
@@ -11,14 +11,17 @@
|
||||
*/
|
||||
#include <dt-bindings/iio/qti_power_supply_iio.h>
|
||||
&pm6125_vadc {
|
||||
/*
|
||||
gpio6_div3{
|
||||
reg = <ADC_GPIO3_DIV3>;
|
||||
label = "gpio3_div3";
|
||||
qcom,pre-scaling = <1 3>;
|
||||
};
|
||||
*/
|
||||
};
|
||||
|
||||
&pm6125_gpios {
|
||||
/*
|
||||
gpio6_adc{
|
||||
gpio6_adc_default:gpio6_adc_default{
|
||||
pins = "gpio6";
|
||||
@@ -26,6 +29,17 @@
|
||||
bias-high-impedance;
|
||||
};
|
||||
};
|
||||
*/
|
||||
|
||||
gpio_7_dig_out {
|
||||
gpio7_dig_out_default: gpio7_dig_out_default {
|
||||
pins = "gpio7";
|
||||
function = "normal";
|
||||
power-source = <1>;
|
||||
output-low;
|
||||
input-disable;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
/*
|
||||
@@ -52,23 +66,25 @@
|
||||
};
|
||||
};*/
|
||||
|
||||
&qupv3_se0_i2c {
|
||||
&qupv3_se1_i2c {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "okay";
|
||||
pinctrl-0 = <&qupv3_se0_i2c_act>;
|
||||
pinctrl-1 = <&qupv3_se0_i2c_sle>;
|
||||
//pinctrl-0 = <&qupv3_se0_i2c_act>;
|
||||
//pinctrl-1 = <&qupv3_se0_i2c_sle>;
|
||||
wt6670: wt6670f@35 {
|
||||
status = "okay";
|
||||
compatible = "mediatek,wt6670f_qc3p";
|
||||
reg = <0x35>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&wt6670_gpio_pins &gpio7_dig_out_default>;
|
||||
#io-channel-cells = <1>;
|
||||
wt6670f-reset-gpio = <&tlmm 68 0x0>;
|
||||
wt6670f-reset-gpio = <&pm6125_gpios 7 0x0>;
|
||||
wt6670f-int-gpio = <&tlmm 93 0x0>;
|
||||
};
|
||||
};
|
||||
|
||||
&qupv3_se0_i2c {
|
||||
&qupv3_se2_i2c {
|
||||
status = "okay";
|
||||
|
||||
cw2217@64 {
|
||||
@@ -97,17 +113,17 @@
|
||||
sm,en_batt_det;
|
||||
//sm,iocv_man_mode;
|
||||
sm,misc = <0x0800>;
|
||||
sm,aging_ctrl = <0x0125>;
|
||||
sm,aging_ctrl = <0x0121>;
|
||||
sm,cycle_cfg = <0x7000>;
|
||||
sm,rsns = <0>;
|
||||
factory_mode_ntc_exist = <0>;
|
||||
sm,fg_irq_set = <0x07FF>;
|
||||
sm,low_soc1 = <1>;
|
||||
sm,low_soc2 = <15>;
|
||||
sm,v_l_alarm = <3400>;
|
||||
sm,v_l_alarm = <3450>;
|
||||
sm,v_h_alarm = <4450>;
|
||||
sm,battery_table_num = <0>;
|
||||
sm,param_version = <2>;
|
||||
sm,param_version = <1>;
|
||||
sm,t_l_alarm_in = <54>;
|
||||
sm,t_h_alarm_in = <1>;
|
||||
sm,t_l_alarm_ex = <0xD3D8>;
|
||||
@@ -121,12 +137,12 @@
|
||||
&qupv3_se1_i2c {
|
||||
status = "okay";
|
||||
|
||||
sgm4154x: sgm4154x@3B {
|
||||
sgm4154x: sgm4154x@1A {
|
||||
status = "okay";
|
||||
compatible = "sgm,sgm41542";
|
||||
reg = <0x3B>;
|
||||
compatible = "sgm,sgm41513";
|
||||
reg = <0x1A>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&sgm4154x_gpio_pins &gpio6_adc_default>;
|
||||
pinctrl-0 = <&sgm4154x_gpio_pins>;
|
||||
#io-channel-cells = <1>;
|
||||
io-channels = <&pm6125_vadc ADC_GPIO3_DIV3>,
|
||||
<&wt6670 PSY_IIO_QC3P_REAL_TYPE>,
|
||||
@@ -145,16 +161,16 @@
|
||||
interrupt-parent = <&tlmm>;
|
||||
interrupts = <96 0>; //irq num base on hardware design
|
||||
sgm,irq-gpio = <&tlmm 96 0>; //irq num base on hardware design
|
||||
sgm,chg-en-gpio = <&tlmm 36 0>; //gpio num base on hardware design 1.MTK parent node name is pio 2.QUALCOMM parent node name is tlmm or other
|
||||
//sgm,chg-en-gpio = <&pio 0 0>; //gpio num base on hardware design 1.MTK parent node name is pio 2.QUALCOMM parent node name is tlmm or other
|
||||
|
||||
dpdm-supply = <&usb2_phy0>;
|
||||
mmi,qc3-support;
|
||||
/* sw jeita parameter customer defined*/
|
||||
enable_sw_jeita;
|
||||
jeita_temp_above_t4_cv = <0>;
|
||||
jeita_temp_t3_to_t4_cv = <4100000>;
|
||||
jeita_temp_t2_to_t3_cv = <4350000>;
|
||||
jeita_temp_t1_to_t2_cv = <4350000>;
|
||||
jeita_temp_t3_to_t4_cv = <4450000>;
|
||||
jeita_temp_t2_to_t3_cv = <4450000>;
|
||||
jeita_temp_t1_to_t2_cv = <4450000>;
|
||||
jeita_temp_t0_to_t1_cv = <0>;
|
||||
jeita_temp_below_t0_cv = <0>;
|
||||
|
||||
@@ -177,93 +193,6 @@
|
||||
temp_neg_10_thres = <0>;
|
||||
};
|
||||
|
||||
|
||||
// bq25890: bq25890@6A {
|
||||
// status = "okay";
|
||||
// compatible = "ti,bq2589x-1";
|
||||
// reg = <0x6A>;
|
||||
|
||||
// pinctrl-names = "default";
|
||||
// pinctrl-0 = <&bq2589x_irq &gpio6_adc_default>;
|
||||
// #io-channel-cells = <1>;
|
||||
// io-channels = <&pm6125_vadc ADC_GPIO3_DIV3>,
|
||||
// <&wt6670 PSY_IIO_QC3P_REAL_TYPE>,
|
||||
// <&wt6670 PSY_IIO_QC3P_POWER>,
|
||||
// <&wt6670 PSY_IIO_START_DETECTION>,
|
||||
// <&wt6670 PSY_IIO_DETECTION_READY>,
|
||||
// <&mmi_chrg PSY_IIO_QC3P_START_POLICY>;
|
||||
|
||||
// io-channel-names = "gpio3_div3",
|
||||
// "wt6670_usb_real_type",
|
||||
// "wt6670_usb_qc3p_power",
|
||||
// "wt6670_start_detection",
|
||||
// "wt6670_detection_ready",
|
||||
// "qc3p_start_policy";
|
||||
|
||||
// bq2589x_irq-gpio = <&tlmm 96 0>;
|
||||
// bq2589x_en-gpio = <&tlmm 36 0>;
|
||||
// dpdm-supply = <&usb2_phy0>;
|
||||
|
||||
// mmi,qc3-support;
|
||||
// ti,bq2589x,vbus-volt-high-level = <8700>;/* tune adapter to output 9v */
|
||||
// ti,bq2589x,vbus-volt-low-level = <4400>;/* tune adapter to output 5v */
|
||||
// ti,bq2589x,vbat-min-volt-to-tuneup = <3000>;
|
||||
// ti,bq2589x,charge-voltage = <4350>;
|
||||
// ti,bq2589x,charge-current = <3250>;
|
||||
// ti,bq2589x,term-current = <256>;
|
||||
// ti,bq2589x,enable-auto-dpdm;
|
||||
// ti,bq2589x,enable-termination;
|
||||
// ti,bq2589x,enable-ico;
|
||||
// ti,bq2589x,use-absolute-vindpm;
|
||||
// };
|
||||
|
||||
/*
|
||||
bq2597x: bq2597x-charger@66 {
|
||||
compatible = "ti,bq25970-charger";
|
||||
reg = <0x66>;
|
||||
#io-channel-cells = <1>;
|
||||
//ti,bq2597x,interrupt_gpios = <&pio 30 0>;
|
||||
//interrupt-parent = <&pio>;
|
||||
//interrupts = <2 IRQ_TYPE_EDGE_FALLING 2 0>;
|
||||
//interrupt-names = "bq2597x_irq";
|
||||
|
||||
//pinctrl-names = "default_slave";
|
||||
//pinctrl-0 = <&bq2597x_int_default_slave>;
|
||||
interrupt-parent = <&tlmm>;
|
||||
interrupts = <3 0>; //irq num base on hardware design
|
||||
bq2597x,irq-gpio = <&tlmm 3 0>; //irq num base on hardware design
|
||||
|
||||
ti,bq2597x,bat-ovp-disable = <0>;
|
||||
ti,bq2597x,bat-ocp_disable = <0>;
|
||||
ti,bq2597x,bat-ovp-alarm-disable = <0>;
|
||||
ti,bq2597x,bus-ocp-disable = <0>;
|
||||
ti,bq2597x,bus-ovp-alarm-disable = <0>;
|
||||
ti,bq2597x,bus-ocp-alarm-disable = <0>;
|
||||
ti,bq2597x,bat-ucp-alarm-disable = <0>;
|
||||
ti,bq2597x,bat-therm-disable = <0>;
|
||||
ti,bq2597x,bus-therm-disable = <0>;
|
||||
|
||||
ti,bq2597x,bat-ovp-threshold = <4500>;
|
||||
ti,bq2597x,bat-ovp-alarm-threshold = <4450>;
|
||||
ti,bq2597x,bat-ocp-threshold = <8000>;
|
||||
ti,bq2597x,bat-ocp-alarm-threshold = <7500>;
|
||||
|
||||
ti,bq2597x,bus-ovp-threshold = <12000>;
|
||||
ti,bq2597x,bus-ovp-alarm-threshold = <11000>;
|
||||
ti,bq2597x,bus-ocp-threshold = <3750>;
|
||||
ti,bq2597x,bus-ocp-alarm-threshold = <3500>;
|
||||
|
||||
ti,bq2597x,bat-ucp-alarm-threshold = <2000>;
|
||||
|
||||
ti,bq2597x,bat-therm-threshold = <0x15>;
|
||||
ti,bq2597x,bus-therm-threshold = <0x15>;
|
||||
ti,bq2597x,die-therm-threshold = <125>;
|
||||
|
||||
ti,bq2597x,ac-ovp-threshold = <17>;
|
||||
ti,bq2597x,sense-resistor-mohm = <5>;
|
||||
};
|
||||
*/
|
||||
|
||||
bq2597x: bq2597x-charger@66 {
|
||||
compatible = "ti,bq25970-charger";
|
||||
reg = <0x66>;
|
||||
@@ -276,8 +205,8 @@
|
||||
//pinctrl-names = "default_slave";
|
||||
//pinctrl-0 = <&bq2597x_int_default_slave>;
|
||||
interrupt-parent = <&tlmm>;
|
||||
interrupts = <3 0>; //irq num base on hardware design
|
||||
bq2597x,irq-gpio = <&tlmm 3 0>; //irq num base on hardware design
|
||||
interrupts = <97 0>; //irq num base on hardware design
|
||||
bq2597x,irq-gpio = <&tlmm 97 0>; //irq num base on hardware design
|
||||
|
||||
ti,bq2597x,bat-ovp-disable = <0>;
|
||||
ti,bq2597x,bat-ocp_disable = <0>;
|
||||
@@ -311,6 +240,7 @@
|
||||
};
|
||||
|
||||
&tlmm{
|
||||
/*
|
||||
qupv3_se0_i2c_pins: qupv3_se0_i2c_pins {
|
||||
qupv3_se0_i2c_act: qupv3_se0_i2c_active {
|
||||
mux {
|
||||
@@ -339,9 +269,25 @@
|
||||
};
|
||||
};
|
||||
};
|
||||
*/
|
||||
|
||||
wt6670_gpio_pins: wt6670_gpio_pins {
|
||||
mux {
|
||||
pins = "gpio93";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio93";
|
||||
drive-strength = <2>;
|
||||
bias-pull-up;
|
||||
input-enable;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
/*
|
||||
wt6670_pins_default: wt6670_default_mode {
|
||||
};
|
||||
wt6670_pins_scl_low: wt6670_scl_low {
|
||||
@@ -394,6 +340,7 @@
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
*/
|
||||
/*
|
||||
wt6670_pins_i2c: wt6670_i2c_mode {
|
||||
pins_cmd_dat {
|
||||
@@ -420,23 +367,6 @@
|
||||
};
|
||||
};
|
||||
|
||||
/*
|
||||
&tlmm {
|
||||
bq2589x_irq: bq2589x_irq {
|
||||
mux {
|
||||
pins = "gpio96";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio96";
|
||||
drive-strength = <2>;
|
||||
bias-pull-up;
|
||||
input-enable;
|
||||
};
|
||||
};
|
||||
};
|
||||
*/
|
||||
|
||||
&soc {
|
||||
mmi_charger: mmi,charger {
|
||||
@@ -464,13 +394,13 @@
|
||||
mmi,demo-fv-mv = <4000>;
|
||||
mmi,otg-cl-ua = <1200000>;
|
||||
mmi,df-serialnum = "SB18D33989";
|
||||
mmi,mmi-temp-zones = <0 4200 1000 0>,
|
||||
<10 4250 3000 1000>,
|
||||
<15 0 3000 3000>,
|
||||
mmi,mmi-temp-zones = <0 4450 2500 0>,
|
||||
<10 4450 2500 1000>,
|
||||
<15 0 2500 2500>,
|
||||
<45 0 4000 4000>,
|
||||
<60 4200 3000 0>;
|
||||
mmi,thermal-mitigation = <4000000 3500000
|
||||
3000000 2500000
|
||||
<60 4200 4000 0>;
|
||||
mmi,thermal-mitigation = <3500000 3000000
|
||||
2800000 2500000
|
||||
2000000 1500000
|
||||
1200000 900000
|
||||
600000 300000>;
|
||||
@@ -530,8 +460,8 @@
|
||||
mmi,qc3p-volt-max = <10000000>;
|
||||
mmi,chrg-temp-zones-num = <5>;
|
||||
mmi,mmi-chrg-temp-zones =
|
||||
<0 4200 1000 0 0>,
|
||||
<10 4250 3000 4450 1000>,
|
||||
<0 4450 1000 0 0>,
|
||||
<10 4450 3000 4450 1000>,
|
||||
<15 4450 3000 0 0>,
|
||||
<45 4350 6000 4480 4000>,
|
||||
<60 4200 4000 0 0>;
|
||||
|
||||
@@ -22,6 +22,7 @@
|
||||
//#include "discrete_charging_hawao.dtsi"
|
||||
//#include "discrete-rt-pd-manger.dtsi"
|
||||
#include "camera/khaje-camera-sensor-mot-devon-overlay.dtsi"
|
||||
#include "discrete_charging_devon.dtsi"
|
||||
|
||||
&firmware {
|
||||
android {
|
||||
@@ -128,8 +129,8 @@
|
||||
};
|
||||
|
||||
&pm6125_vadc {
|
||||
pinctrl-0 = <&camera_therm_default &emmc_therm_default &chg_therm_default>;
|
||||
|
||||
pinctrl-0 = <&camera_therm_default &emmc_therm_default>;
|
||||
/*
|
||||
chg_therm {
|
||||
reg = <ADC_GPIO4_PU2>;
|
||||
label = "chg_therm";
|
||||
@@ -137,29 +138,33 @@
|
||||
qcom,hw-settle-time = <200>;
|
||||
qcom,pre-scaling = <1 1>;
|
||||
};
|
||||
*/
|
||||
};
|
||||
|
||||
&pm6125_adc_tm {
|
||||
io-channels = <&pm6125_vadc ADC_AMUX_THM1_PU2>,
|
||||
<&pm6125_vadc ADC_AMUX_THM2_PU2>,
|
||||
<&pm6125_vadc ADC_XO_THERM_PU2>,
|
||||
<&pm6125_vadc ADC_GPIO4_PU2>;
|
||||
<&pm6125_vadc ADC_XO_THERM_PU2>;
|
||||
//<&pm6125_vadc ADC_GPIO4_PU2>;
|
||||
|
||||
/*
|
||||
chg_therm {
|
||||
reg = <ADC_GPIO4_PU2>;
|
||||
qcom,ratiometric;
|
||||
qcom,hw-settle-time = <200>;
|
||||
};
|
||||
*/
|
||||
};
|
||||
|
||||
&pm6125_gpios {
|
||||
|
||||
/*
|
||||
chg_therm {
|
||||
chg_therm_default: chg_therm_default {
|
||||
pins = "gpio7";
|
||||
bias-high-impedance;
|
||||
};
|
||||
};
|
||||
*/
|
||||
};
|
||||
|
||||
&thermal_zones {
|
||||
@@ -215,6 +220,7 @@
|
||||
};
|
||||
};
|
||||
|
||||
/*
|
||||
chg_therm {
|
||||
polling-delay-passive = <0>;
|
||||
polling-delay = <0>;
|
||||
@@ -229,6 +235,7 @@
|
||||
};
|
||||
};
|
||||
};
|
||||
*/
|
||||
|
||||
msm_therm {
|
||||
polling-delay-passive = <0>;
|
||||
|
||||
@@ -31,7 +31,7 @@
|
||||
output-low;
|
||||
};
|
||||
};
|
||||
|
||||
#if 0
|
||||
cam_flash_tx_active: cam_flash_tx_active {
|
||||
/* TX */
|
||||
mux {
|
||||
@@ -60,7 +60,7 @@
|
||||
output-low;
|
||||
};
|
||||
};
|
||||
|
||||
#endif
|
||||
nfc {
|
||||
nfc_clk_req_active {
|
||||
/* active state */
|
||||
|
||||
Reference in new issue
Block a user