arm/dts: init device tree for capri
inherit device tree from guam update device tree with capri specific changes Change-Id: Icdbe45e8caf18859bac140668cef8b005b3a5bcc Reviewed-on: https://gerrit.mot.com/1743604 SLTApproved: Slta Waiver SME-Granted: SME Approvals Granted Tested-by: Jira Key Reviewed-by: Wang Wang <wangwang1@lenovo.com> Submit-Approved: Jira Key
This commit is contained in:
liujg6 authored and Carlos Pinho committed
1 parent
1de54a992f
commit
61a19f46d3
8 files changed
+1124
No files matched your search
@@ -57,6 +57,11 @@ dtbo-$(CONFIG_CEBU_DTB) += \
|
||||
|
||||
bengal-cebu-evt-overlay.dtbo-base := bengal-moto-base-cebu.dtb
|
||||
|
||||
dtbo-$(CONFIG_CAPRI_DTB) += \
|
||||
bengal-capri-evt-overlay.dtbo
|
||||
|
||||
bengal-capri-evt-overlay.dtbo-base := bengal-moto-base.dtb
|
||||
|
||||
else
|
||||
ifeq ($(CONFIG_BUILD_ARM64_DT_OVERLAY),y)
|
||||
dtbo-$(CONFIG_ARCH_KONA) += \
|
||||
|
||||
@@ -0,0 +1,138 @@
|
||||
/* Copyright (c) 2019, The Linux Foundation. All rights reserved.
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 and
|
||||
* only version 2 as published by the Free Software Foundation.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*/
|
||||
|
||||
#include <dt-bindings/interrupt-controller/irq.h>
|
||||
|
||||
&wsa881x_i2c_e {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&wsa881x_i2c_44 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&wsa881x_analog_clk_gpio {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&wsa881x_analog_reset_gpio {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&wsa881x_analog_clk {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&qupv3_se1_i2c {
|
||||
status = "ok"
|
||||
|
||||
/* AWINIC AW882XX mono Smart PA */
|
||||
aw882xx_smartpa@34 {
|
||||
compatible = "awinic,aw882xx_smartpa";
|
||||
reg = <0x34>;
|
||||
reset-gpio = <&tlmm 97 0>;
|
||||
/*irq-gpio = <&tlmm 136 0x2008>; */
|
||||
monitor-flag = <1>;
|
||||
monitor-timer-val = <3000>;
|
||||
status = "okay";
|
||||
|
||||
afe-rx-portid = <0x1000>;
|
||||
afe-tx-portid = <0x1001>;
|
||||
|
||||
low-vol-table-down = <3650 9 3 3750 9 2 3900 9 1>;
|
||||
low-vol-table-up = <4000 9 0 3800 9 1 3700 9 2>;
|
||||
|
||||
low-temp-table-down = <0xFFFFFFFB 0x4 0x10 0xFFBEAE7E 0x0 0x5 0x9 0xFFD80505 0x5 0x6 0x6 0xFFED714D>;
|
||||
low-temp-table-up = <0x7 0x9 0x0 0x00000000 0x2 0x6 0x06 0xFFED714D 0xFFFFFFE 0x05 0x09 0xFFD80505>;
|
||||
};
|
||||
/* AWINIC AW882XX mono Smart PA End */
|
||||
};
|
||||
|
||||
/* Add pinctrl for MI2S0 */
|
||||
&soc {
|
||||
cdc_pri_mi2s_gpios: msm_cdc_pinctrl_pri {
|
||||
compatible = "qcom,msm-cdc-pinctrl";
|
||||
pinctrl-names = "aud_active", "aud_sleep";
|
||||
pinctrl-0 = <&lpi_i2s1_sck_active &lpi_i2s1_ws_active
|
||||
&lpi_i2s1_sd0_active &lpi_i2s1_sd1_active>;
|
||||
pinctrl-1 = <&lpi_i2s1_sck_sleep &lpi_i2s1_ws_sleep
|
||||
&lpi_i2s1_sd0_sleep &lpi_i2s1_sd1_sleep>;
|
||||
};
|
||||
};
|
||||
|
||||
/* Configure MI2S0 SD0&SD1 */
|
||||
&dai_mi2s0 {
|
||||
/* SD0 line for playback */
|
||||
qcom,msm-mi2s-rx-lines = <1>;
|
||||
/* SD1 line for recording(SmartPA EC) */
|
||||
qcom,msm-mi2s-tx-lines = <2>;
|
||||
};
|
||||
|
||||
/* Modify btfmslim_codec's compatible */
|
||||
&btfmslim_codec {
|
||||
compatible = "btfmslim_slave";
|
||||
status = "ok"
|
||||
};
|
||||
|
||||
|
||||
&bengal_snd {
|
||||
qcom,model = "bengal-awinic-snd-card";
|
||||
aw,have-882xx = <1>;
|
||||
|
||||
qcom,audio-routing =
|
||||
"AMIC1", "MIC BIAS1",
|
||||
"MIC BIAS1", "Analog Mic1",
|
||||
"AMIC2", "MIC BIAS2",
|
||||
"MIC BIAS2", "Analog Mic2",
|
||||
"AMIC3", "MIC BIAS3",
|
||||
"MIC BIAS3", "Analog Mic3",
|
||||
"IN1_HPHL", "HPHL_OUT",
|
||||
"IN2_HPHR", "HPHR_OUT",
|
||||
"IN3_AUX", "AUX_OUT",
|
||||
"TX SWR_MIC0", "ADC1_OUTPUT",
|
||||
"TX SWR_MIC4", "ADC2_OUTPUT",
|
||||
"TX SWR_MIC0", "VA_TX_SWR_CLK",
|
||||
"TX SWR_MIC1", "VA_TX_SWR_CLK",
|
||||
"TX SWR_MIC2", "VA_TX_SWR_CLK",
|
||||
"TX SWR_MIC3", "VA_TX_SWR_CLK",
|
||||
"TX SWR_MIC4", "VA_TX_SWR_CLK",
|
||||
"RX_TX DEC0_INP", "TX DEC0 MUX",
|
||||
"RX_TX DEC1_INP", "TX DEC1 MUX",
|
||||
"RX_TX DEC2_INP", "TX DEC2 MUX",
|
||||
"RX_TX DEC3_INP", "TX DEC3 MUX",
|
||||
"TX_AIF1 CAP", "VA_TX_SWR_CLK",
|
||||
"TX_AIF2 CAP", "VA_TX_SWR_CLK",
|
||||
"TX_AIF3 CAP", "VA_TX_SWR_CLK",
|
||||
"VA SWR_MIC0", "ADC1_OUTPUT",
|
||||
"VA SWR_MIC4", "ADC2_OUTPUT";
|
||||
|
||||
qcom,mi2s-audio-intf = <1>;
|
||||
qcom,pri-mi2s-gpios = <&cdc_pri_mi2s_gpios>;
|
||||
/delete-property/ qcom,cdc-dmic01-gpios;
|
||||
/delete-property/ qcom,cdc-dmic23-gpios;
|
||||
|
||||
qcom,wsa-max-devs = <0>;
|
||||
qcom,wsa-devs = <0>;
|
||||
};
|
||||
|
||||
&cdc_dmic01_gpios {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&cdc_dmic23_gpios {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
/* Modify headset's BIAS voltage to 2.6V */
|
||||
&wcd937x_codec {
|
||||
qcom,cdc-micbias2-mv = <2600>;
|
||||
};
|
||||
@@ -0,0 +1,264 @@
|
||||
/* Copyright (c) 2019, The Linux Foundation. All rights reserved.
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 and
|
||||
* only version 2 as published by the Free Software Foundation.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*/
|
||||
|
||||
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
||||
#include "bengal-moto-common-overlay.dtsi"
|
||||
#include "bengal-capri-display.dtsi"
|
||||
#include "bengal-audio-overlay.dtsi"
|
||||
#include "bengal-capri-touchscreen-overlay.dtsi"
|
||||
#include "camera/bengal-camera-sensor-mot-capri-overlay.dtsi"
|
||||
#include "bengal-capri-fps.dtsi"
|
||||
#include "bengal-capri-moto-thermal.dtsi"
|
||||
|
||||
&firmware {
|
||||
android {
|
||||
vbmeta {
|
||||
compatible = "android,vbmeta";
|
||||
parts = "vbmeta,boot,system,vendor,dtbo";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&qupv3_se4_2uart {
|
||||
status = "ok"
|
||||
};
|
||||
|
||||
|
||||
&pm6125_gpios {
|
||||
|
||||
key_vol_up {
|
||||
key_vol_up_default: key_vol_up_default {
|
||||
pins = "gpio5";
|
||||
function = "normal";
|
||||
input-enable;
|
||||
bias-pull-up;
|
||||
power-source = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm{
|
||||
tlmm_gpio_key {
|
||||
gpio_key_active: gpio_key_active {
|
||||
mux {
|
||||
pins = "gpio33";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio33";
|
||||
drive-strength = <2>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&soc {
|
||||
/delete-node/ qupv3_se0_spi;
|
||||
|
||||
gpio_keys {
|
||||
compatible = "gpio-keys";
|
||||
label = "gpio-keys";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&key_vol_up_default &gpio_key_active>;
|
||||
|
||||
vol_up {
|
||||
label = "volume_up";
|
||||
gpios = <&pm6125_gpios 5 GPIO_ACTIVE_LOW>;
|
||||
linux,input-type = <1>;
|
||||
linux,code = <KEY_VOLUMEUP>;
|
||||
linux,can-disable;
|
||||
debounce-interval = <15>;
|
||||
gpio-key,wakeup;
|
||||
};
|
||||
|
||||
assist_key{
|
||||
label = "assist_key";
|
||||
gpios = <&tlmm 33 0x1>;
|
||||
linux,input-type = <1>;
|
||||
linux,code = <KEY_SEARCH>;
|
||||
debounce-interval = <15>;
|
||||
linux,can-disable;
|
||||
gpio-key,wakeup;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
|
||||
&sdhc_1 {
|
||||
vdd-supply = <&L24A>;
|
||||
qcom,vdd-voltage-level = <2960000 2960000>;
|
||||
qcom,vdd-current-level = <0 570000>;
|
||||
|
||||
vdd-io-supply = <&L11A>;
|
||||
qcom,vdd-io-always-on;
|
||||
qcom,vdd-io-lpm-sup;
|
||||
qcom,vdd-io-voltage-level = <1800000 1800000>;
|
||||
qcom,vdd-io-current-level = <0 325000>;
|
||||
|
||||
pinctrl-names = "active", "sleep";
|
||||
pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on
|
||||
&sdc1_rclk_on>;
|
||||
pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off
|
||||
&sdc1_rclk_off>;
|
||||
|
||||
status = "ok"
|
||||
};
|
||||
|
||||
&sdhc_2 {
|
||||
vdd-supply = <&L22A>;
|
||||
qcom,vdd-voltage-level = <2960000 2960000>;
|
||||
qcom,vdd-current-level = <0 800000>;
|
||||
|
||||
vdd-io-supply = <&L5A>;
|
||||
qcom,vdd-io-voltage-level = <1800000 2960000>;
|
||||
qcom,vdd-io-current-level = <0 22000>;
|
||||
|
||||
pinctrl-names = "active", "sleep";
|
||||
pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
|
||||
pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
|
||||
|
||||
cd-gpios = <&tlmm 88 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
status = "ok"
|
||||
};
|
||||
|
||||
&ufsphy_mem {
|
||||
compatible = "qcom,ufs-phy-qmp-v3-660";
|
||||
|
||||
vdda-phy-supply = <&L4A>; /* 0.9v */
|
||||
vdda-pll-supply = <&L12A>; /* 1.8v */
|
||||
vdda-phy-max-microamp = <51400>;
|
||||
vdda-pll-max-microamp = <14200>;
|
||||
|
||||
status = "ok"
|
||||
};
|
||||
|
||||
&ufshc_mem {
|
||||
vdd-hba-supply = <&gcc_ufs_phy_gdsc>;
|
||||
vdd-hba-fixed-regulator;
|
||||
vcc-supply = <&L24A>;
|
||||
vcc-voltage-level = <2950000 2960000>;
|
||||
vccq2-supply = <&L11A>;
|
||||
vcc-max-microamp = <600000>;
|
||||
vccq2-max-microamp = <600000>;
|
||||
|
||||
qcom,vddp-ref-clk-supply = <&L18A>;
|
||||
qcom,vddp-ref-clk-max-microamp = <100>;
|
||||
qcom,vddp-ref-clk-min-uV = <1232000>;
|
||||
qcom,vddp-ref-clk-max-uV = <1232000>;
|
||||
|
||||
status = "ok"
|
||||
};
|
||||
|
||||
&sde_dsi {
|
||||
qcom,dsi-default-panel = <&dsi_hlt_hx83102d_video>;
|
||||
};
|
||||
|
||||
&soc{
|
||||
mtp_batterydata: qcom,battery-data {
|
||||
qcom,batt-id-range-pct = <15>;
|
||||
df-serialnum = "SB18C77591";
|
||||
#include "qg-batterydata-jk50-atl-4850mah.dtsi"
|
||||
#include "qg-batterydata-jk50-scud-4850mah.dtsi"
|
||||
#include "qg-batterydata-jk50-atl-flex-4850mah.dtsi"
|
||||
#include "qg-batterydata-jk50-atl-unicoba-4850mah.dtsi"
|
||||
#include "qg-batterydata-jk50-swd-4850mah.dtsi"
|
||||
};
|
||||
};
|
||||
|
||||
&pmi632_qg {
|
||||
qcom,qg-iterm-ma = <350>;
|
||||
qcom,vbatt-cutoff-mv = <3200>;
|
||||
qcom,vbatt-empty-mv = <3000>;
|
||||
qcom,vbatt-low-mv = <3300>;
|
||||
qcom,vbatt-low-cold-mv = <3500>;
|
||||
qcom,battery-data = <&mtp_batterydata>;
|
||||
qcom,rbat-conn-mohm = <10>;
|
||||
qcom,cl-feedback-on;
|
||||
qcom,cl-min-start-soc = <0>;
|
||||
qcom,cl-max-start-soc = <5>;
|
||||
qcom,cl-min-temp = <150>;
|
||||
qcom,cl-max-temp = <450>;
|
||||
qcom,cl-max-increment = <5>;
|
||||
qcom,cl-max-decrement = <10>;
|
||||
qcom,cl-min-limit = <200>;
|
||||
qcom,cl-max-limit = <30>;
|
||||
qcom,s3-entry-ibat-ua = <15000>;
|
||||
qcom,s3-exit-ibat-ua = <35000>;
|
||||
qcom,vbatt-empty-cold-mv = <3000>;
|
||||
qcom,ignore-shutdown-soc-secs = <1800>;
|
||||
qcom.hold-soc-while-full;
|
||||
qcom,linearize-soc;
|
||||
};
|
||||
|
||||
&pmi632_rgb {
|
||||
red {
|
||||
label = "charging";
|
||||
};
|
||||
};
|
||||
|
||||
&pmi632_charger {
|
||||
qcom,iterm-ma = <100>;
|
||||
qcom,fcc-max-ua = <2000000>;
|
||||
qcom,fv-max-uv = <4400000>;
|
||||
qcom,usb-icl-ua = <2000000>;
|
||||
qcom,thermal-mitigation = <2000>,
|
||||
<1800>,
|
||||
<1600>,
|
||||
<1300>,
|
||||
<1100>,
|
||||
<900>,
|
||||
<600>,
|
||||
<400>;
|
||||
qcom,battery-data = <&mtp_batterydata>;
|
||||
qcom,mmi-temp-zones = <0 4200 1000 0>,
|
||||
<10 4200 1000 1000>,
|
||||
<15 0 1000 1000>,
|
||||
<45 0 2000 2000>,
|
||||
<60 4200 2000 0>;
|
||||
qcom,enable-charging-limit;
|
||||
qcom,upper-limit-capacity = <70>;
|
||||
qcom,lower-limit-capacity = <60>;
|
||||
qcom,dr_supported;
|
||||
qcom,hvdcp-disable;
|
||||
qcom,otg-cl-ua = <1000000>;
|
||||
qcom,dc-unsupported;
|
||||
qcom,wireless-unsupported;
|
||||
qcom,usbeb-unsupported;
|
||||
qcom,disable-suspend-on-collapse;
|
||||
dpdm-supply = <&qusb_phy0>;
|
||||
qcom,auto-recharge-soc = <99>;
|
||||
qcom,support-microb-dcp;
|
||||
};
|
||||
|
||||
&soc {
|
||||
qcom,tz_gpio {
|
||||
compatible = "qcom,tz_gpio";
|
||||
tlmm-tz = <14>,
|
||||
<15>,
|
||||
<16>,
|
||||
<17>;
|
||||
};
|
||||
};
|
||||
&spmi_bus {
|
||||
qcom,pm6125@0 {
|
||||
qpnp-power-on-mmi@800 {
|
||||
compatible = "qcom,qpnp-power-on-mmi";
|
||||
interrupts = <0x0 0x8 0x3 IRQ_TYPE_EDGE_BOTH>;
|
||||
interrupt-names = "kpdpwr-bark";
|
||||
};
|
||||
};
|
||||
};
|
||||
@@ -0,0 +1,246 @@
|
||||
#include <dt-bindings/clock/mdss-14nm-pll-clk.h>
|
||||
#include "bengal-sde-display.dtsi"
|
||||
#include "dsi-panel-mot-dummy-qhd-video.dtsi"
|
||||
#include "dsi-panel-moto-hx83102d-hlt-hdplus-video.dtsi"
|
||||
#include "dsi-panel-moto-nt36525b-djn-hdplus-video.dtsi"
|
||||
#include "dsi-panel-moto-icnl9911s-tm-hdplus-video.dtsi"
|
||||
#include "dsi-panel-moto-ili9882h-hlt-hdplus-video.dtsi"
|
||||
#include "dsi-panel-moto-ili9882n-tm-hdplus-video.dtsi"
|
||||
|
||||
&sde_dsi {
|
||||
//qcom,platform-mot-ext-feature-enable;
|
||||
//qcom,platform-mot-early-power-enable;
|
||||
};
|
||||
|
||||
&dsi_panel_pwr_supply {
|
||||
qcom,panel-supply-entry@2 {
|
||||
qcom,supply-pre-off-sleep = <2>;
|
||||
};
|
||||
};
|
||||
|
||||
&dsi_hlt_hx83102d_video {
|
||||
qcom,mdss-dsi-t-clk-post = <0x0B>;
|
||||
qcom,mdss-dsi-t-clk-pre = <0x23>;
|
||||
qcom,dsi-select-clocks = "mux_byte_clk0", "mux_pixel_clk0",
|
||||
"src_byte_clk0", "src_pixel_clk0",
|
||||
"shadow_byte_clk0", "shadow_pixel_clk0";
|
||||
|
||||
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
||||
qcom,mdss-dsi-bl-min-level = <16>;
|
||||
qcom,mdss-dsi-bl-max-level = <4095>;
|
||||
qcom,bklt-dcs-2bytes-enabled;
|
||||
qcom,mdss-brightness-max-level = <4095>;
|
||||
qcom,mdss-dsi-hbm-type = "lcd-dcs-only";
|
||||
qcom,mdss-dsi-panel-hbm-is-51cmd;
|
||||
|
||||
qcom,esd-check-enabled;
|
||||
qcom,mdss-dsi-panel-status-check-mode = "reg_read";
|
||||
qcom,mdss-dsi-panel-status-command =[06 01 00 01 00 00 01 0a];
|
||||
qcom,mdss-dsi-panel-status-command-state = "dsi_lp_mode";
|
||||
qcom,mdss-dsi-panel-status-value = <0x9d>;
|
||||
qcom,mdss-dsi-panel-status-read-length = <4>;
|
||||
qcom,mdss-dsi-panel-status-valid-params = <1>;
|
||||
qcom,mdss-dsi-no-panel-on-read-support;
|
||||
|
||||
qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
|
||||
qcom,platform-reset-gpio = <&tlmm 82 0>;
|
||||
|
||||
qcom,mdss-dsi-display-timings {
|
||||
timing@0 {
|
||||
qcom,mdss-dsi-panel-phy-timings =
|
||||
[1F 1C 05 06 03 02 04 a0
|
||||
1F 1C 05 06 03 02 04 a0
|
||||
1F 1C 05 06 03 02 04 a0
|
||||
1F 1C 05 06 03 02 04 a0
|
||||
1F 11 05 06 03 02 04 a0];
|
||||
qcom,display-topology = <1 0 1>;
|
||||
qcom,default-topology-index = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&dsi_djn_nt36525b_video {
|
||||
qcom,mdss-dsi-t-clk-post = <0x0a>;
|
||||
qcom,mdss-dsi-t-clk-pre = <0x20>;
|
||||
qcom,dsi-select-clocks = "mux_byte_clk0", "mux_pixel_clk0",
|
||||
"src_byte_clk0", "src_pixel_clk0",
|
||||
"shadow_byte_clk0", "shadow_pixel_clk0";
|
||||
|
||||
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
||||
qcom,mdss-dsi-bl-min-level = <1>;
|
||||
qcom,mdss-dsi-bl-max-level = <255>;
|
||||
//qcom,bklt-dcs-2bytes-enabled;
|
||||
qcom,mdss-brightness-max-level = <255>;
|
||||
qcom,mdss-dsi-hbm-type = "lcd-dcs-only";
|
||||
qcom,mdss-dsi-panel-hbm-is-51cmd;
|
||||
|
||||
qcom,esd-check-enabled;
|
||||
qcom,mdss-dsi-panel-status-check-mode = "reg_read";
|
||||
qcom,mdss-dsi-panel-status-command =[06 01 00 01 00 00 01 0a];
|
||||
qcom,mdss-dsi-panel-status-command-state = "dsi_lp_mode";
|
||||
qcom,mdss-dsi-panel-status-value = <0x9c>;
|
||||
qcom,mdss-dsi-panel-status-read-length = <1>;
|
||||
qcom,mdss-dsi-no-panel-on-read-support;
|
||||
|
||||
qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
|
||||
qcom,platform-reset-gpio = <&tlmm 82 0>;
|
||||
|
||||
qcom,mdss-dsi-display-timings {
|
||||
timing@0 {
|
||||
qcom,mdss-dsi-panel-phy-timings =
|
||||
[1F 1C 04 06 03 03 04 a0
|
||||
1F 1C 04 06 03 03 04 a0
|
||||
1F 1C 04 06 03 03 04 a0
|
||||
1F 1C 04 06 03 03 04 a0
|
||||
1F 0F 04 06 03 03 04 a0];
|
||||
qcom,display-topology = <1 0 1>;
|
||||
qcom,default-topology-index = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&dsi_tm_icnl9911s_video {
|
||||
qcom,mdss-dsi-t-clk-post = <0x0a>;
|
||||
qcom,mdss-dsi-t-clk-pre = <0x20>;
|
||||
qcom,dsi-select-clocks = "mux_byte_clk0", "mux_pixel_clk0",
|
||||
"src_byte_clk0", "src_pixel_clk0",
|
||||
"shadow_byte_clk0", "shadow_pixel_clk0";
|
||||
|
||||
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
||||
qcom,mdss-dsi-bl-min-level = <16>;
|
||||
qcom,mdss-dsi-bl-max-level = <4095>;
|
||||
qcom,bklt-dcs-2bytes-enabled;
|
||||
qcom,mdss-brightness-max-level = <4095>;
|
||||
qcom,mdss-dsi-hbm-type = "lcd-dcs-only";
|
||||
qcom,mdss-dsi-panel-hbm-is-51cmd;
|
||||
|
||||
qcom,esd-check-enabled;
|
||||
qcom,mdss-dsi-panel-status-check-mode = "reg_read";
|
||||
qcom,mdss-dsi-panel-status-command =[06 01 00 01 00 00 01 0a];
|
||||
qcom,mdss-dsi-panel-status-command-state = "dsi_lp_mode";
|
||||
qcom,mdss-dsi-panel-status-value = <0x9c>;
|
||||
qcom,mdss-dsi-panel-status-read-length = <1>;
|
||||
qcom,mdss-dsi-no-panel-on-read-support;
|
||||
qcom,platform-reset-gpio-always-on;
|
||||
|
||||
qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
|
||||
qcom,platform-reset-gpio = <&tlmm 82 0>;
|
||||
|
||||
qcom,mdss-dsi-display-timings {
|
||||
timing@0 {
|
||||
qcom,mdss-dsi-panel-phy-timings =
|
||||
[1F 1C 04 06 03 02 04 a0
|
||||
1F 1C 04 06 03 02 04 a0
|
||||
1F 1C 04 06 03 02 04 a0
|
||||
1F 1C 04 06 03 02 04 a0
|
||||
1F 0F 04 06 03 02 04 a0];
|
||||
qcom,display-topology = <1 0 1>;
|
||||
qcom,default-topology-index = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&dsi_hlt_ili9882h_video {
|
||||
qcom,mdss-dsi-t-clk-post = <0x0A>;
|
||||
qcom,mdss-dsi-t-clk-pre = <0x21>;
|
||||
qcom,dsi-select-clocks = "mux_byte_clk0", "mux_pixel_clk0",
|
||||
"src_byte_clk0", "src_pixel_clk0",
|
||||
"shadow_byte_clk0", "shadow_pixel_clk0";
|
||||
|
||||
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
||||
qcom,mdss-dsi-bl-min-level = <16>;
|
||||
qcom,mdss-dsi-bl-max-level = <4095>;
|
||||
qcom,bklt-dcs-2bytes-enabled;
|
||||
qcom,mdss-brightness-max-level = <4095>;
|
||||
qcom,mdss-dsi-hbm-type = "lcd-dcs-only";
|
||||
qcom,mdss-dsi-panel-hbm-is-51cmd;
|
||||
|
||||
// qcom,esd-check-enabled;
|
||||
qcom,mdss-dsi-panel-status-check-mode = "reg_read";
|
||||
qcom,mdss-dsi-panel-status-command =[06 01 00 01 00 00 01 0a];
|
||||
qcom,mdss-dsi-panel-status-command-state = "dsi_lp_mode";
|
||||
qcom,mdss-dsi-panel-status-value = <0x9c>;
|
||||
qcom,mdss-dsi-panel-status-read-length = <4>;
|
||||
qcom,mdss-dsi-panel-status-valid-params = <1>;
|
||||
qcom,mdss-dsi-no-panel-on-read-support;
|
||||
|
||||
qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
|
||||
qcom,platform-reset-gpio = <&tlmm 82 0>;
|
||||
|
||||
qcom,mdss-dsi-display-timings {
|
||||
timing@0 {
|
||||
qcom,mdss-dsi-panel-phy-timings =
|
||||
[1F 1C 05 06 03 02 04 a0
|
||||
1F 1C 05 06 03 02 04 a0
|
||||
1F 1C 05 06 03 02 04 a0
|
||||
1F 1C 05 06 03 02 04 a0
|
||||
1F 0F 05 06 03 02 04 a0];
|
||||
qcom,display-topology = <1 0 1>;
|
||||
qcom,default-topology-index = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&dsi_tm_ili9882n_video {
|
||||
qcom,mdss-dsi-t-clk-post = <0x0A>;
|
||||
qcom,mdss-dsi-t-clk-pre = <0x1E>;
|
||||
qcom,dsi-select-clocks = "mux_byte_clk0", "mux_pixel_clk0",
|
||||
"src_byte_clk0", "src_pixel_clk0",
|
||||
"shadow_byte_clk0", "shadow_pixel_clk0";
|
||||
|
||||
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
||||
qcom,mdss-dsi-bl-min-level = <16>;
|
||||
qcom,mdss-dsi-bl-max-level = <4095>;
|
||||
qcom,bklt-dcs-2bytes-enabled;
|
||||
qcom,mdss-brightness-max-level = <4095>;
|
||||
qcom,mdss-dsi-hbm-type = "lcd-dcs-only";
|
||||
qcom,mdss-dsi-panel-hbm-is-51cmd;
|
||||
|
||||
// qcom,esd-check-enabled;
|
||||
qcom,mdss-dsi-panel-status-check-mode = "reg_read";
|
||||
qcom,mdss-dsi-panel-status-command =[06 01 00 01 00 00 01 0a];
|
||||
qcom,mdss-dsi-panel-status-command-state = "dsi_lp_mode";
|
||||
qcom,mdss-dsi-panel-status-value = <0x9d>;
|
||||
qcom,mdss-dsi-panel-status-read-length = <4>;
|
||||
qcom,mdss-dsi-panel-status-valid-params = <1>;
|
||||
qcom,mdss-dsi-no-panel-on-read-support;
|
||||
|
||||
qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
|
||||
qcom,platform-reset-gpio = <&tlmm 82 0>;
|
||||
|
||||
qcom,mdss-dsi-display-timings {
|
||||
timing@0 {
|
||||
qcom,mdss-dsi-panel-phy-timings =
|
||||
[1F 1C 05 06 03 02 04 a0
|
||||
1F 1C 05 06 03 02 04 a0
|
||||
1F 1C 05 06 03 02 04 a0
|
||||
1F 1C 05 06 03 02 04 a0
|
||||
1F 10 05 06 03 02 04 a0];
|
||||
qcom,display-topology = <1 0 1>;
|
||||
qcom,default-topology-index = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mot_dummy_vid_qhd {
|
||||
qcom,dsi-select-clocks = "mux_byte_clk0", "mux_pixel_clk0",
|
||||
"src_byte_clk0", "src_pixel_clk0",
|
||||
"shadow_byte_clk0", "shadow_pixel_clk0";
|
||||
|
||||
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
||||
qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
|
||||
qcom,platform-reset-gpio = <&tlmm 82 0>;
|
||||
|
||||
qcom,mdss-dsi-display-timings {
|
||||
timing@0 {
|
||||
qcom,mdss-dsi-panel-phy-timings =
|
||||
[1F 1B 05 06 03 03 04 a0
|
||||
1F 1B 05 06 03 03 04 a0
|
||||
1F 1B 05 06 03 03 04 a0
|
||||
1F 1B 05 06 03 03 04 a0
|
||||
1F 10 04 06 03 03 04 a0];
|
||||
qcom,display-topology = <1 0 1>;
|
||||
qcom,default-topology-index = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
@@ -0,0 +1,28 @@
|
||||
/* Copyright (c) 2020, The Linux Foundation. All rights reserved.
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 and
|
||||
* only version 2 as published by the Free Software Foundation.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
/plugin/;
|
||||
|
||||
#include "bengal-capri-common-overlay.dtsi"
|
||||
#include "bengal-capri-awinic-audio-overlay.dtsi"
|
||||
|
||||
/ {
|
||||
model = "capri";
|
||||
compatible = "qcom,bengal-capri", "qcom,bengal-moto", "qcom,bengal";
|
||||
qcom,msm-id = <417 0x10000>;
|
||||
qcom,board-id = <0 0xA000>;
|
||||
};
|
||||
|
||||
/*
|
||||
* capri HW rev specific changes go here
|
||||
*/
|
||||
@@ -0,0 +1,146 @@
|
||||
|
||||
&tlmm {
|
||||
fps_rst_active: fps_rst_active {
|
||||
/* active state */
|
||||
mux {
|
||||
pins = "gpio104";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio104";
|
||||
drive-strength = <2>; /* 2 MA */
|
||||
output-low;
|
||||
};
|
||||
};
|
||||
|
||||
fps_rst_suspend: fps_rst_suspend {
|
||||
/* sleep state */
|
||||
mux {
|
||||
pins = "gpio104";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio104";
|
||||
drive-strength = <2>; /* 2 MA */
|
||||
};
|
||||
};
|
||||
|
||||
fps_int_active: fps_int_active {
|
||||
/* active state */
|
||||
mux {
|
||||
pins = "gpio65";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio65";
|
||||
drive-strength = <2>; /* 2 MA */
|
||||
bias-disable;
|
||||
input-enable;
|
||||
};
|
||||
};
|
||||
|
||||
fps_int_suspend: fps_int_suspend {
|
||||
/* sleep state */
|
||||
mux {
|
||||
pins = "gpio65";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio65";
|
||||
drive-strength = <2>; /* 2 MA */
|
||||
bias-disable;
|
||||
input-enable;
|
||||
};
|
||||
};
|
||||
|
||||
fps_ido3_en_active: ldo3_en_active {
|
||||
/* active state */
|
||||
mux {
|
||||
pins = "gpio34";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio34";
|
||||
drive-strength = <2>; /* 2 MA */
|
||||
bias-pull-up;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
|
||||
fps_ido3_en_suspend: ldo3_en_suspend {
|
||||
/* suspend state */
|
||||
mux {
|
||||
pins = "gpio34";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio34";
|
||||
drive-strength = <2>; /* 2 MA */
|
||||
bias-pull-up;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
|
||||
fps_ido1p8_en_active: ldo1p8_en_active {
|
||||
/* active state */
|
||||
mux {
|
||||
pins = "gpio106";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio106";
|
||||
drive-strength = <2>; /* 2 MA */
|
||||
bias-pull-up;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
|
||||
fps_ido1p8_en_suspend: ldo1p8_en_suspend {
|
||||
/* suspend state */
|
||||
mux {
|
||||
pins = "gpio106";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio106";
|
||||
drive-strength = <2>; /* 2 MA */
|
||||
bias-pull-up;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&soc {
|
||||
goodix_fingerprint{
|
||||
//status = "/chosen", "mmi,fps", "true";
|
||||
status = "ok"
|
||||
compatible = "goodix,fingerprint";
|
||||
fp-gpio-reset = <&tlmm 104 0x00>;
|
||||
fp-gpio-irq = <&tlmm 65 0x00>;
|
||||
fp-gpio-ven = <&tlmm 34 0x00>;
|
||||
interrupt-parent = <&tlmm>;
|
||||
interrupts = <65 0>;
|
||||
interrupt-controller;
|
||||
pinctrl-names = "default", "suspend";
|
||||
pinctrl-0 = <&fps_rst_active &fps_int_active &fps_ido3_en_active>;
|
||||
pinctrl-1 = <&fps_rst_suspend &fps_int_suspend &fps_ido3_en_suspend>;
|
||||
};
|
||||
|
||||
fpc: fpc_fpc1020 {
|
||||
compatible = "fpc,fpc1020";
|
||||
status = "ok"
|
||||
irq = <&tlmm 65 0>;
|
||||
rst = <&tlmm 104 0>;
|
||||
pinctrl-names = "default", "suspend";
|
||||
pinctrl-0 = <&fps_rst_active &fps_int_active>;
|
||||
pinctrl-1 = <&fps_rst_suspend &fps_int_suspend>;
|
||||
};
|
||||
};
|
||||
@@ -0,0 +1,110 @@
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/iio/qcom,spmi-vadc.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
&soc {
|
||||
sys_temp_support {
|
||||
compatible = "mmi,sys-temp";
|
||||
mmi,temperature-names = "front_temp",
|
||||
"back_temp";
|
||||
status = "ok"
|
||||
};
|
||||
};
|
||||
|
||||
&thermal_zones {
|
||||
camera-therm-usr {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
camera_therm {
|
||||
polling-delay-passive = <0>;
|
||||
polling-delay = <0>;
|
||||
thermal-governor = "user_space";
|
||||
thermal-sensors = <&pm6125_adc_tm_iio ADC_GPIO1_PU2>;
|
||||
wake-capable-sensor;
|
||||
trips {
|
||||
active-config0 {
|
||||
temperature = <125000>;
|
||||
hysteresis = <1000>;
|
||||
type = "passive";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
xo-therm-usr {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
xo_therm {
|
||||
polling-delay-passive = <0>;
|
||||
polling-delay = <0>;
|
||||
thermal-governor = "user_space";
|
||||
thermal-sensors = <&pm6125_adc_tm ADC_XO_THERM_PU2>;
|
||||
wake-capable-sensor;
|
||||
trips {
|
||||
active-config0 {
|
||||
temperature = <125000>;
|
||||
hysteresis = <1000>;
|
||||
type = "passive";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
pa-therm0-usr {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
pa_therm0 {
|
||||
polling-delay-passive = <0>;
|
||||
polling-delay = <0>;
|
||||
thermal-governor = "user_space";
|
||||
thermal-sensors = <&pm6125_adc_tm ADC_AMUX_THM1_PU2>;
|
||||
wake-capable-sensor;
|
||||
trips {
|
||||
active-config0 {
|
||||
temperature = <125000>;
|
||||
hysteresis = <1000>;
|
||||
type = "passive";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
quiet-therm-usr {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
msm_therm {
|
||||
polling-delay-passive = <0>;
|
||||
polling-delay = <0>;
|
||||
thermal-governor = "user_space";
|
||||
thermal-sensors = <&pm6125_adc_tm ADC_AMUX_THM2_PU2>;
|
||||
wake-capable-sensor;
|
||||
trips {
|
||||
active-config0 {
|
||||
temperature = <125000>;
|
||||
hysteresis = <1000>;
|
||||
type = "passive";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
chg-skin-therm-usr {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
chg_therm {
|
||||
polling-delay-passive = <0>;
|
||||
polling-delay = <0>;
|
||||
thermal-governor = "user_space";
|
||||
thermal-sensors = <&pmi632_adc_tm ADC_GPIO2_PU2>;
|
||||
wake-capable-sensor;
|
||||
trips {
|
||||
active-config0 {
|
||||
temperature = <125000>;
|
||||
hysteresis = <1000>;
|
||||
type = "passive";
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@@ -0,0 +1,187 @@
|
||||
&tlmm{
|
||||
pmx_ts_int_active {
|
||||
ts_int_active: ts_int_active {
|
||||
mux {
|
||||
pins = "gpio67";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio67";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
pmx_ts_int_suspend {
|
||||
ts_int_suspend: ts_int_suspend {
|
||||
mux {
|
||||
pins = "gpio67";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio67";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
};
|
||||
pmx_ts_reset_active {
|
||||
ts_reset_active: ts_reset_active {
|
||||
mux {
|
||||
pins = "gpio66";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio66";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
pmx_ts_reset_suspend {
|
||||
ts_reset_suspend: ts_reset_suspend {
|
||||
mux {
|
||||
pins = "gpio66";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio66";
|
||||
drive-strength = <2>;
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
};
|
||||
pmx_ts_release {
|
||||
ts_release: ts_release {
|
||||
mux {
|
||||
pins = "gpio67", "gpio66";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio67", "gpio66";
|
||||
drive-strength = <2>;
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
};
|
||||
ts_int_pull_up: ts_int_pull_up {
|
||||
mux {
|
||||
pins = "gpio67";
|
||||
function = "gpio";
|
||||
};
|
||||
config {
|
||||
pins = "gpio67";
|
||||
drive-strength = <6>;
|
||||
input-enable;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&qupv3_se2_spi_pins {
|
||||
qupv3_se2_spi_sleep: qupv3_se2_spi_sleep {
|
||||
mux {
|
||||
pins = "gpio6", "gpio7","gpio71";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio6", "gpio7","gpio71";
|
||||
drive-strength = <6>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
qupv3_se2_cs_sleep: qupv3_se2_cs_sleep {
|
||||
mux {
|
||||
pins = "gpio80";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio80";
|
||||
drive-strength = <6>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&qupv3_se2_spi {
|
||||
status = "ok"
|
||||
qcom,spi-touch-active="himax,hxcommon";
|
||||
pinctrl-1 = <&qupv3_se2_spi_sleep &qupv3_se2_cs_sleep>;
|
||||
himax_0flash_ts@0 {
|
||||
compatible = "himax,hxcommon";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <10000000>;
|
||||
spi-cpha;
|
||||
himax,panel-coords = <0 720 0 1600>;
|
||||
himax,display-coords = <0 720 0 1600>;
|
||||
/* himax,touch_info = <32 18 0 720 1600 10 0 1>;*/
|
||||
himax,irq-gpio = <&tlmm 67 0x2008>;
|
||||
himax,rst-gpio = <&tlmm 66 0x00>;
|
||||
himax,def-build-id = <0x1203>;
|
||||
himax,def-config-id = <0x0002>;
|
||||
report_type = <1>;
|
||||
interrupt-parent = <&tlmm>;
|
||||
interrupts = <67 0x02>;
|
||||
/* lab-supply = <&lcdb_ldo_vreg>;
|
||||
ibb-supply = <&lcdb_ncp_vreg>;*/
|
||||
pinctrl-names = "pmx_ts_active","pmx_ts_suspend";
|
||||
pinctrl-0 = <&ts_int_active &ts_reset_active>;
|
||||
pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
|
||||
panel = <&dsi_hlt_hx83102d_video>;
|
||||
};
|
||||
ilitek@1{
|
||||
compatible = "tchip,ilitek";
|
||||
reg = <0x1>;
|
||||
interrupt-parent = <&tlmm>;
|
||||
interrupts = <67 0x2008>;
|
||||
spi-max-frequency = <10000000>;
|
||||
spi-cpha;
|
||||
spi-cpol;
|
||||
touch,reset-gpio = <&tlmm 66 0x00>;
|
||||
touch,irq-gpio = <&tlmm 67 0x2008>;
|
||||
panel = <&dsi_hlt_ili9882h_video>;
|
||||
panel2 = <&dsi_tm_ili9882n_video>;
|
||||
};
|
||||
chipone_tddi@2 {
|
||||
compatible = "chipone-tddi";
|
||||
reg = <2>;
|
||||
interrupt-parent = <&tlmm>;
|
||||
spi-max-frequency = <4000000>;
|
||||
spi-cpha;
|
||||
spi-cpol;
|
||||
interrupts = <67 0x02>;
|
||||
chipone,rst-gpio = <&tlmm 66 0x00>;
|
||||
chipone,irq-gpio = <&tlmm 67 0x2008>;
|
||||
chipone,x-res = <720>;
|
||||
chipone,y-res = <1600>;
|
||||
chipone,def-build-id = <0x010a>;
|
||||
chipone,def-config-id = <0x0001>;
|
||||
panel = <&dsi_tm_icnl9911s_video>;
|
||||
};
|
||||
nova_0flash_ts@3 {
|
||||
compatible = "novatek,NVT-ts-spi";
|
||||
reg = <3>;
|
||||
spi-max-frequency = <9600000>;
|
||||
novatek,swrst-n8-addr = <0x03F0FE>;
|
||||
novatek,spi-rd-fast-addr = <0x03F310>;
|
||||
spi-cpha;
|
||||
novatek,irq-gpio = <&tlmm 67 0x2008>;
|
||||
novatek,reset-gpio = <&tlmm 66 0x00>;
|
||||
report_type = <1>;
|
||||
novatek,def-max-resolution = <720 1600>;
|
||||
interrupt-parent = <&tlmm>;
|
||||
interrupts = <67 0x02>;
|
||||
pinctrl-names = "pmx_ts_active","pmx_ts_suspend";
|
||||
pinctrl-0 = <&ts_int_active &ts_reset_active>;
|
||||
pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
|
||||
};
|
||||
};
|
||||
Reference in new issue
Block a user